Algunos Proveedores de lamparas y/o bulbos para proyector , le pueden vender la lampara para el reemplazo de su lampara dañada o el portalamparas completo

Si Ud. Tiene un cierto grado tecnico o habilidad manual y es muy cuidadoso entonces reemplazar su lampara es una buena idea.

De lo contrario Lo mejor es comprar el portalamparas nuevo, ya que si se aventura a cambiar la lampara unicamente , puede entrar en un trabajo dificil y causar un daño al portalamparas o a la misma lampara.

Las diferencias de costos entre ambos es minima y el riesgo por daños es mayor.

Comentarios Utiles a saber sobre los bulbos o lamparas para proyector

Se fabrican 2 tipos de bulbos o lamparas:

Bulbos de Halógeno:

Estos tiene un periodo de vida de aproximadamente de 70 Hs.

Durante su periodo de vida-Actividad producen un brillo constante y una imagen amarrillenta.

Su costo es relativamente bajo , desde 40 a 80 Dll’s

Lámparas de haluro de metal UHB (Ultra Alto Brillo):

Su periodo de vida en promedio es de 2000 Hs.

Estas producen una imagen mas blanca y su brillo disminuye lentamente durante su vida-Actividad

Su costo es mayor, desde los 200 a 400 Dll’s

La aplicacion de estas lamparas para proyector las decide el fabricante.

¿Y que hay sobre UHP (Ultra Alto Rendimiento)?

Esta es una tecnologia propia y desarrollada por Philips, que requiere de un menor Voltaje de operacion para las mismas prestaciones de brillo y son de menor tamaño , haciendolas mas confiables al trabajar a menor voltaje… menor temperatura y mayor tiempo de vida , aproximadamente 4000 Hs.

(Sitio, En Ingles con mas detalles sobre esta tecnologia)

Una manera de cuidar y prolongar la vida util de su proyector es utilizarlo en areas bien ventiladas , no obstruir sus areas de ventilacion y limpiar frecuentemente sus filtros de aire , desde luego observar todas las recomendaciones de su manual del usuario.

Dentro de la pagina les presentamos unas fotografias de algunos portalamparas para proyector Hitachi sus probables intercambios y otros datos tecnicos de interes general , esperando les sea de utilidad y de apoyo en alguna compra de Bulbo para proyector .

Checa esta empresa no solo tiene el portalamparas Hitachi , tiene mas lamparas y partes para tu TV DLP Plasma y LCD . Cuentan con servicio de envio directo de Lamparas y partes a tu domicilo y en todas las ciudades del mundo.

http://www.discount-merchant.com/

Do you have a projection TV with a bad lamp? Is the lamp inside your TV a Philips or OSRAM 100W, 1oo/120W, or a 120W lamp? Does it say 1.3 just after the wattage? If so, click here for the lowest price on an original replacement from Discount-Merchant.com

If you have an OSRAM lamp in your TV we highly recommend replacing that lamp with a Philips. It’s no secret Philips is the innovator of Ultra High Pressure (UHP) Mercury Lamps (created in 1995). The quality and dependability of Philips lamps are much greater than OSRAM, or any of the generic brands out there (LTI, APO, etc.. The combination of better “burners” and more advanced drivers (the ballasts) are a few reasons why Philips lamps outlast the competition.

In any case, if your lamp is a 100W, 100/120W, or 120W and looks like the lamps in the pictures below, we recommend purchasing this lamp from Discount-Merchant.com. Post questions and concerns!

The Panasonic PT-50LC13 is a high definition television that uses the plasma technology and has a screen size of 50 inches when measured diagonally. As far as the plasma technology is concerned, Panasonic is one of the best and they have proved it time and again. The design of the Panasonic PT-50LC13 is very simple yet classy. The cabinet of this flat screen television is very modest and is fully silver in color. The front side of the cabinet has been given a clean look except for the Panasonic logo. The speakers are located to the sides of the widescreen, which makes the cabinet of the set even wider. This makes the set very short and wide.

The native display resolution offered by the Panasonic PT-50LC13 is 720p, which means that it has a vertical resolution of 1280 pixels and a horizontal resolution of 720 pixels. Also, this rear projection television will accept all input resolutions upto 1080i. This means that any input signal other than 720p will either be up converted or down converted to fit the available display resolution. The dimensions of the set are 55.8 inches in width, 35.3 inches in height and 15.3 inches in depth. The set tips the weigh scales at just a little less than 83 pounds, which is quite creditable considering the screen size.

Discount-Merchant.com is among the nation’s largest plasma and LCD TVs replacement parts providers. If you need replacement PCBs, remotes, outer cases, stands, or anything else related to Plasma and LCD TVs, visit Discount-Merchant.com

Well…instead of writing individual pages for various “How-To” guides, we have created a single page.  We will update this page as more guides are made available.  If you have a request for a specific enclosure, please let us know!

 http://www.fixyourdlp.com/lampguides/guides.html

For the best price on the Panasonic TY-LA1000 Lamp Enclosure, click here.

Thes attached PDF is the lamp replacement guide written by Panasonic:
panasonic-tyla1000-lamp-instructions.pdf

The instructions are intuitive and easy to follow.  If you have any problems downloading the file and/or replacing your lamp, ask your questions here.

 From our knowledge, this enclosure is compatible with the following TVs:

PT43LC14     PT-43LC14
PT43LCX64  PT-43LCX64
PT44LCX65  PT-44LCX65
PT50LC13     PT-50LC13
PT50LC14     PT-50LC14
PT50LCX63  PT-50LCX63
PT50LCX64  PT-50LCX64
PT52LCX15   PT-52LCX15
PT52LCX15B PT-52LCX15B
PT52LCX35  PT-52LCX35
PT52LCX65  PT-52LCX65
PT60LC13     PT-60LC13
PT60LC14     PT-60LC14
PT60LCX63  PT-60LCX63
PT60LCX64  PT-60LCX64
PT61LCX35   PT-61LCX35
PT61LCX65   PT-61LCX65

An IMPORTANT NOTE: Be weary of replacement “lamps” or “bulbs” for the TY-LA1000 sold without the enclosure housing.  Typically, buying the lamp-only is okay, as long as the customer is purchasing an original lamp.  Always stay away from off-brand bulbs manufactured by OSRAM, LTI, APO, or another third-party provider for your Panasonic TY-LA1000.   When purchasing just the lamp itself (even an original), it can be a hassle unless you’re fairly good with a technician’s soldering iron.

Your original enclosure has the lamp cable connectors soldered from it’s terminals to the connector plug.  When purchasing just the lamp alone, you will have to cut this connector and soldering it on your new lamp.  Sounds confusing or difficult?  It is…and until we make a kit for it, I don’t suggest anyone purchase the bare bulb only!

To avoid all the hassle, just purchase the whole enclosure.  For the best price on the TY-LA1000 Enclosure, click here.