Install a new Optoma PRO350 projector lamp

This quick guide will show you how to install a new projector lamp for your Optoma PRO350 projector.

The Optoma PRO350 projector uses the Optoma BL-FU185A. When the Optoma PRO350 projector lamp has reached end of life,  the lamp warning message flash on screen. This means you have no more than 30 hours before the bulb will burn out. You may aslso notice the Lamp-LED light flashing red and the picture quality starting to get poor resolution.

Change the Optoma BL-FU185A projector lamp in your Optoma PRO150S immediately.

Authentic projector lamps are critical!

You’ll want the best projector lamp for your Optoma PRO350 and that means buying directly from an authorized manufacturer. Look for the seal of approval. Avoid generic lamps for the following reasons:

• generics have shorter lamp life than originals
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projectors
• no safeguards in place to protect your eyesight
• installing a generic lamp voids your projector’s warranty.

Learn how to spot copycat lamps posing as authentic lamps.

Find this lamp on Amazon sold by these authorized dealers:

• Optoma BL-FU185A Projector lamp – UHP – 185 Watt – for Optoma DS316, ES526, EW536, EX536, Pro350, TS526, TW536, TX536, Home Theater Series HD66
• Optoma BL-FU185A, UHP, 185W Projector Lamp
• Optoma BL-FU185A Projector lamp – UHP – 185 Watt – for Optoma DS316, ES526, EW536, EX536, Pro350, TS526, TW536, TX536, Home Theater Series HD66 by Optoma
  

Installing the Optoma BL-FU185A projector lamp

Before replacing the Optoma BL-FU185A projector lamp follow these crucial safety tips to prevent injury to yourself or the projector:

• Switch off the power to the Optoma PRO350 projector by pressing the Power/Standby button.
• Disconnect the power cord.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the PRO350 projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A projector lamp in place.

Note: The used Optoma BL-FU185A  projector lamp contains mercury and should be properly recycled.

4. Lift up the wire handle on the Optoma BL-FU185A  projector lamp and slowly remove it from the projector. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Install the new Optoma BL-FU185A  projector lamp:

• Remove the new Optoma BL-FU185A projector lamp from its packaging.
• Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma PRO350 projector.
• Tighten the two screws on the projector lamp.
• Replace the lamp cover and tighten its two screws. Reset the lamp timer.

Reset the Lamp Replacement Timer

The Optoma PRO350 projector has an automatic lamp timer that tracks the numbers of hours left in the projector lamp. When the Optoma BL-FU185A (SP.8EH01GC01) projector lamp is approaching end of life, the lamp replacement timer will trigger the warning system. If you don’t reset the lamp replacement timer you run the risk of the projector lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Lamp Replacement Timer:

• Turn on the projector.
• Using the remote press MENU
• Select OPTIONS
• Select LAMP SETTINGS
• Select LAMP RESET
• Select YES.
• Press MENU to exit.

Extend the life of the Optoma BL-FU185A projector lamp:

• Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
• Keep your air filters clean to avoid overheating the projector.
• Every 24 hours, turn off the projector and let it stand for 1 hour
• Make sure there is enough airflow around the Optoma PRO350 projector particularly if it’s been permanently mounted.

Learn more with Top tips for extending DLP projector lamp life.