Hitachi CP-X206 projector lamp

Need to change the Hitachi CP-X206 projector lamp? Follow this guide to learn how.

Tracking the projector lamp life

Watch for these signs that the Hitachi CP-X206 projector lamp is reaching its end of life:

Both the Hitachi CP-X206 Power and Lamp Indicators are flashing red while the Temp Indicator is turned off.
Color tone on the screen may also appear weak or washed out.
Picture has poor color quality.
Always be ready for replacing the lamp. Keep track of projector lamp life so you’ll know when to replace the Hitachi CP-X206 projector projector.

Authentic lamps

Keep your Hitachi CP-X206 projector working at its optimum levels by only installing an OEM authentic replacement projector lamp. Avoid generics by looking for the seal of approval before purchasing.

Despite their bargain prices, knockoff generics have a shorter life than original lamps and are also prone to explosions. They are usually missing any safeguards to protect your eyesight from damage and also offer no protection from the toxic substitute parts used. Copycat manufacturers also don’t have the equipment to properly calibrate the lamps fully so they can easily damage the sensitive optics in your Hitachi CP-X206 projector

Learn to spot copycat lamps posing as authentic lamps.

Find this lamp sold on Amazon by these authorized distributors:

<br>

Install the Hitachi DT00841 projector lamp

The Hitachi CP-X206 projector uses the Hitachi DT00841. Before installing the new projector lamp, follow these safety measures

Turn off the Hitachi CP-X206 projector.
Unplug the power cord.
Allow the projector to cool for at least 45 minutes. It should be cool to the touch. This projector works using high heat and there is danger you can be burned.
NOTE: If the projector is mounted on the ceiling, don’t stand underneath the projector while opening the cover.

Prepare the new Hitachi CP-X206 projector lamp. If the projector is mounted on a ceiling, or if the lamp has broken, contact your dealer for assistance.
Loosen the screw (marked by arrow) of the lamp cover and then slide the lamp cover to the side to remove it.
Loosen the 2 screws (marked by arrow) of the projector lamp, and slowly pick up the lamp by the handles. Be careful not the bang the lamp. The Hitachi DT00841 projector lamp contains mercury and must be recycled properly. Do not throw it in regular garbage.
Insert the new lamp, taking care not to touch the actual bulb. Oil in your fingers will cause a dark spot on the lamp when it heats up.
Tighten the two screws of the Hitachi DT00841 projector lamp that were loosened to remove the old projector lamp.
Slide the lamp cover back in place and firmly fasten the screw of the lamp cover.
Turn on the projector and set the lamp timer:

To reset the projector lamp timer:

Note: Reset the projector lamp time only when you have replaced the lamp so the Hitachi CP-X206 projector can properly track the lamp life. Otherwise you run the risk of using the lamp beyond its lamp life.

Press the MENU button
Scroll down to the GO TO ADVANCED MENU option. Press ENTER
Scroll down to the OPTION menu in the left column and press ENTER.
Scroll down to LAMP TIME. Press ENTER To make a dialogue field appear
Scroll up to the RESET option on the dialogue box.
The lamp setting will be set to zero.

Replacing the air filters

Get more hours from your Hitachi DT00841 by keeping your air filters clean to avoid overheating the projector.

Pull the filter frame’s knob up while holding the filter cover. The filter frame will come off and the air filter will appear.
Take out the old air filter and insert the new air filter.
Put the filter frame back.
Put the filter unit back into the projector
Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU.
Learn more with Top tips for extending DLP projector lamp life.

Green your projector

Recycle your lamp housing by only replacing the Hitachi CP-X206 lamp. Our training video shows you how to do it. It’s easy!

Installing a Hitachi CP-X206 projector lamp