About Us - Page 100 of 171 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

Eliminate Samsung HLT5689SX/XAA white dots with a new 4719-001997 DLP Chip

Shelagh McNallyPosted on October 26, 2012 Posted in FixYourDLP, Rear Projection TV Lamp Replacement — No Comments ↓

Are white dots on your Samsung HLT5689SX/XAA ruining your picture? Replace the DLP Chip

Replace your 4719-001997 DLP Chip for under $300 and get rid of those white dots on your Samsung HLT5689SX/XAA .

Note: These instructions can also be used for the following Samsung models:

50A650C1FXZA, HLT5055WX/XAA , HLT5076SX/XAA , HLT5087SX/XAA, HLS5087WX/XAA, HL56A650C1FXZA, HLT5656WX/XAA, HLT5676SX/XAA , HLT5687SX/XAA , HLT5687SAX/XAA, HLT5689SX/XAA , HLT6156WX/XAA , HL61A650C1FXZA, HL61A750A1FXZA , HLT6156WX /XAA, HLT6176SX/XAA , HLT6187SAX/XAA , HLT6187SX/XAA , HLS6187WX/XAA, HLT6189SX/XAA, HL67A750A1FXZA, HLT6756WX/XAA, HL72A650C1FXZA, HLT7288WX/XAA

Find this New Mitsubishi/Toshiba 4719-001997 DLP Chip 1910-6143W on Amazon.

Equipment needed

- Electric Philips screwdriver
- needle nose pliers or a 5mm nut driver
- antistatic gloves OR plastic gloves used with an antistatic wrist band
- soft cloth or brush

Replacing the 4719-001997 DLP Chip

4719-001997 DLP Chip, Samsung HLT5689SX RPTV

Step 1

Step 1: Put on the plastic gloves. Loosen all the screws found on the back panel. Put the screws to one side and remove the back panel.

Step 2

Step 2: Loosen the two screws holding the lamp bracket in place.

Step 3

Step 3: Remove the 4 screws holding the lamp engine in place. Disconnect all the connectors. Important: don’t yank any cables.

Step 4

Step 4: Carefully remove light engine from the cabinet.

Step 5

Step 5: Remove the 2 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 6

Step 6: Carefully disconnect the cables between the terminal board and lamp.

Step 7

Step 7: Disconnect the clip connecting the cooling unit.

Step 8

Step 8: Remove the cooling unit and terminal board.

Step 9

Step 9: Remove the terminal board.

Step 10

Step 10: Loosen the 7 screws holding the terminal cover in place. (Good time to dust this section).

Step 11

Step 11: Carefully pop the terminal out of its holder.

Step 12

Step 12: Unlock the old DLP Chip from the terminal. You may need to use a flat edged screwdriver to pop it out.

Step 13

Step 13: Place the new DLP chip into place. Handle the DMD DLP CHIP only by the edges because it is very sensitive to static electricity.

Step 14

Step 14: Put the terminal back into its holder.

Step 15

Step 15: Tighten the 7 screws holding the terminal in place.

Step 16

Step 16: Replace the terminal board’s cover.

Step 17

Step 17: Reconnect the clip holding the cooling unit.

Step 18

Step 18: Re-connect the cables between the terminal board and lamp.

Step 19

Step 19: Tighten the 2 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 20

Step 20: Carefully replace the light engine back into the cabinet.

Step 21

Step 21: Replace and tighten the 4 screws holding the lamp engine in place. Re-connect all the connectors.

Step 22

Step 22: Put the light engine back into the RPTV. Tighten both screws that keep the back bracket in place.

Step 23

Step 23: Put the back cover back onto the TV. Put the screws into the holes and tighten them. Now Enjoy the crisp, clear picture on your Samsung HLT5689SX/XAA RPTV.

Learn more about your Samsung HLT5689SX/XAA RPTV.:

Shop on Amazon for this chip.

Tagged with: 4719-001997 DLP Chip, affordable solution to white death problem, Samsung HLT5689SX/XAA

Look for the seal of approval when buying projector lamps

Shelagh McNallyPosted on October 24, 2012 Posted in Counterfeit Lamp Awareness, FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Only a few companies sell authentic projector lamps. Make sure you’re buying from a recognized authorized dealer.

The Internet has been flooded with companies selling “generic” projector lamps. Many claim to be compatible with your projector. Only a few companies actually are selling OEM (Original Equipment Manufacturer) that are genuine.

It may be tempting to buy a cheaper generic replacement but that may end up costing you more in the long run.

DLP lamps sophisticated technology

DLP Projectors use high pressure to generate light and this pressure needs to be controlled inside the lamp. Authentic projector lamps have been calibrated to the exact wattage. Generic lamps have not designed to handle the subtleties in wattage and pressure. They give off either too much wattage so are prone to overheating and explosions. When generic lamps also give off too little pressure the result is low light and poor picture quality.

Not all lamps are equal

The official brand lamp manufactured by Philips Lighting handles over 60% of the projector lamp market. They’ve spent millions of dollars creating a product that works with the sophisticated mechanism in various projector brands. These lamps are also created with the highest safety standards and with the correct materials. Generic lamps are usually thrown together in order to sell quickly.

Look for the seal of approval

When you purchase from an authorized manufacturer and dealer, you know you’re receiving a Philips bulb that is reliable, durable and safe. Philips gives select companies its Global Premium Partner status. This seal of approval guarantees that the company is selling high quality lamps guaranteed to deliver the best performance while protecting your health and your projector.

Generic brands sold through the Internet can’t offer this kind of guarantee, particularly those manufactured in China, where the standards are lower and regulations not as strict. Installing a cheaper brand may actually damage other sensitive components connected to your projectors operating system. You may also find your warranty has become void after installing these third-party parts.

The few dollars you save with generic “compatible” lamps is not worth it in the long run. Save yourself unnecessary headaches — buy a You’ll be getting a far superior product with a replacement guarantee and tech support.

6 good reasons to avoid generics

generics have a shorter lamp life than original lamps
compatible are created with toxic materials and carcinogenic parts including Krypton-85
knock off lamps are prone to explosions
generic lamps damage the sensitive electronics in your projectors
when you buy copy-cat lamps you get no guarantee or refunds
installing a generic lamp voids your projector’s warranty.

Protect yourself and ask for the Philips seal of approval before buying any projector lamps off the Internet.

Learn the 7 Ways to spot a counterfeit lamp.

Tagged with: authentic projector lamps, avoiding generic lamps, Global Premium Partner status, how to find authentic projector lamps, spot the counterfeit lamps

Install a new 4719-001997 DLP Chip to get rid of Samsung HLT5687SX/XAA white dots

Shelagh McNallyPosted on October 24, 2012 Posted in FixYourDLP, Rear Projection TV Lamp Replacement — No Comments ↓

Are white dots ruining the picture on your Samsung HLT5687SX/XAA picture?

The solution is a new 4719-001997 DLP Chip. Follow our instructions for a no hassle replacement.

Note: These instructions can also be used for the following Samsung models:

Find this New Mitsubishi/Toshiba 4719-001997 DLP Chip 1910-6143W on Amazon.

Equipment needed

- - Electric Philips screwdriver
  - needle nose pliers or a 5mm nut driver
  - antistatic gloves OR plastic gloves used with an antistatic wrist band
  - soft cloth or brush

Replacing the 4719-001997 DLP Chip

4719-001997 DLP Chip, Samsung HLT5687SX RPTV

Step 1

Step 1: Put on the plastic gloves. Loosen all the screws found on the back panel. Put the screws to one side and remove the back panel.

Step 2

Step 2: Loosen the two screws holding the lamp bracket in place.

Step 3

Step 3: Remove the 4 screws holding the lamp engine in place. Disconnect all the connectors. Important: don’t yank any cables.

Step 4

Step 4: Carefully remove light engine from the cabinet.

Step 5

Step 5: Remove the 2 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 6

Step 6: Carefully disconnect the cables between the terminal board and lamp.

Step 7

Step 7: Disconnect the clip connecting the cooling unit.

Step 8

Step 8: Remove the cooling unit and terminal board.

Step 9

Step 9: Remove the terminal board.

Step 10

Step 10: Loosen the 7 screws holding the terminal cover in place. (Good time to dust this section).

Step 11

Step 11: Carefully pop the terminal out of its holder.

Step 12

Step 12: Unlock the old DLP Chip from the terminal. You may need to use a flat edged screwdriver to pop it out.

Step 13

Step 13: Place the new DLP chip into place. Handle the DMD DLP CHIP only by the edges because it is very sensitive to static electricity.

Step 14

Step 14: Put the terminal back into its holder.

Step 15

Step 15: Tighten the 7 screws holding the terminal in place.

Step 16

Step 16: Replace the terminal board’s cover.

Step 17

Step 17: Reconnect the clip holding the cooling unit.

Step 18

Step 18: Re-connect the cables between the terminal board and lamp.

Step 19

Step 19: Tighten the 2 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 20

Step 20: Carefully replace the light engine back into the cabinet.

Step 21

Step 21: Replace and tighten the 4 screws holding the lamp engine in place. Re-connect all the connectors.

Step 22

Step 22: Put the light engine back into the RPTV. Tighten both screws that keep the back bracket in place.

Step 23

Step 23: Put the back panel onto the TV. Put the screws back into place and tighten them. Enjoy the crisp, clear picture on your Samsung HLT5687SX/XAA RPTV.

Learn more about your Samsung HLT5687SX/XAA RPTV:

Shop on Amazon for this chip.

Tagged with: 4719-001997 DLP Chip, affordable solution to white death problem, Samsung HLT5687SX/XAA, white dot Samsung

Replace the BenQ 65.J4002.001 lamp

Shelagh McNallyPosted on October 24, 2012 Posted in FixYourDLP, Rear Projection TV Lamp Replacement — No Comments ↓

You can expect up to 2000 hours of life when you install an authentic BenQ 65.J4002.001 lamp.

Watch for the warning messages that the BenQ 65.J4002.001 lamp is approaching end of life:

The picture looks faded on screen.
The Lamp Indicator blinks red.
Warning Messages about the lamp appear on screen.

Finding the correct lamp

It can be confusing finding the correct BenQ 65.J4002.001 lamp for your BenQ projector. There are hundreds of website selling projector lamps but most of there lamps are knock-off generic lamps that you should avoid at all costs.

Generic “compatible” lamps may appear to be a bargain–however generic knock-off lamps are actually not that great a bargain.

6 good reasons to avoid generics

generics have a shorter lamp life than original lamps
compatible are created with toxic materials and carcinogenic parts including Krypton-85
knock off lamps are prone to explosions
generic lamps damage the sensitive electronics in your projectors
when you buy copy-cat lamps you get no guarantee or refunds
installing a generic lamp voids your projector’s warranty.

The few dollars you save with generic “compatible” lamps is not worth it in the long run. Save yourself unnecessary headaches — buy a BenQ 65.J4002.001 lamp from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Learn the 7 Ways to spot a counterfeit lamp.

Compatible Projectors

The BenQ 65.J4002.001 is compatible with:

BenQ PB8140

BenQ PB8240

For step-by-step instructions on replacing your BenQ 65.J4002.001 projector lamp, click on your projector listed below:

Click here for step-by-step instructions on how to change the BenQ 65.J4002.001 projector lamp for the BenQ PB8140 projector.

Click here for step-by-step instructions on how to change the BenQ 65.J4002.001 projector lamp for the BenQ PB8240 projector.

Extending the life of the BenQ 65.J4002.001 lamp:

Keep your air filters clean to avoid overheating the projector.
Use the Lamp Power option on the BenQ projector and set to Economic Mode to reduce the amount of power used but extend lamp life.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, BenQ 65.J4002.001 lamp, BenQ PB8140 projector, BenQ PB8240 projector, BenQ projector lamps, genuine projector lamps, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting

Fix Samsung HLT5676SX/XAA white death with a new 4719-001997 DLP Chip

Shelagh McNallyPosted on October 23, 2012 Posted in FixYourDLP, Rear Projection TV Lamp Replacement — No Comments ↓

Eliminate dots on your Samsung HLT5676SX/XAA by replacing the 4719-001997 DLP Chip

Replace your 4719-001997 DLP Chip for under $300 and get rid of those white dots.

Note: These instructions can also be used for the following Samsung models:

Find this New Mitsubishi/Toshiba 4719-001997 DLP Chip 1910-6143W on Amazon.

Equipment needed

- Electric Philips screwdriver
- needle nose pliers or a 5mm nut driver
- antistatic gloves OR plastic gloves used with an antistatic wrist band
- soft cloth or brush

Replacing the 4719-001997 DLP Chip

4719-001997 DLP Chip, Samsung HLT5676SX RPTV

Step 1

Step 1: Put on the plastic gloves. Loosen all the screws found on the back panel. Put the screws to one side and remove the back panel.

Step 2

Step 2: Loosen the two screws holding the lamp bracket in place.

Step 3

Step 3: Remove the 4 screws holding the lamp engine in place. Disconnect all the connectors. Important: don’t yank any cables.

Step 4

Step 4: Carefully remove light engine from the cabinet.

Step 5

Step 5: Remove the 2 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 6

Step 6: Carefully disconnect the cables between the terminal board and lamp.

Step 7

Step 7: Disconnect the clip connecting the cooling unit.

Step 8

Step 8: Remove the cooling unit and terminal board.

Step 9

Step 9: Remove the terminal board.

Step 10

Step 10: Loosen the 7 screws holding the terminal cover in place. (Good time to dust this section).

Step 11

Step 11: Carefully pop the terminal out of its holder.

Step 12

Step 12: Unlock the old DLP Chip from the terminal. You may need to use a flat edged screwdriver to pop it out.

Step 13

Step 13: Place the new DLP chip into place. Handle the DMD DLP CHIP only by the edges because it is very sensitive to static electricity.

Step 14

Step 14: Put the terminal back into its holder.

Step 15

Step 15: Tighten the 7 screws holding the terminal in place.

Step 16

Step 16: Replace the terminal board’s cover.

Step 17

Step 17: Reconnect the clip holding the cooling unit.

Step 18

Step 18: Re-connect the cables between the terminal board and lamp.

Step 19

Step 19: Tighten the 2 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 20

Step 20: Carefully replace the light engine back into the cabinet.

Step 21

Step 21: Replace and tighten the 4 screws holding the lamp engine in place. Re-connect all the connectors.

Step 22

Step 22: Put the light engine back into the RPTV. Tighten both screws that keep the back bracket in place.

Step 23

Step 23: Put the back panel onto the TV. Put the screws back into place and tighten them. Enjoy the crisp, clear picture on your Samsung HLT5676SX/XAA RPTV.

Learn more about your Samsung HLT5676SX/XAA RPTV:

Shop on Amazon for this chip.

Tagged with: 4719-001997 DLP Chip, affordable solution to white death problem, Samsung HLT5676SX RPTV

Replace the BenQ PB8240 projector lamp in 3 easy steps

Shelagh McNallyPosted on October 23, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow our guide to replace the BenQ 65.J4002.001 projector lamp in your BenQ PB8240 projector in 3 easy steps.

Step 1: Be prepared — buy an authentic projector lamp

Be ready to replace the lamp by first buying the correct BenQ 65.J4002.001 projector lamp for your BenQ PB8240 projector.

At first glance, a generic compatible projector lamp seems like an incredible bargain. But when you factor in their shorter life spans and poor illumination along with other problems, these lamps actually end up costing more in the long run. These are NOT authentic lamps and should be avoided for the following reasons:

shorter lamp life than original lamps
toxic materials and carcinogenic parts including Krypton-85
prone to explosions
incompatibility causing damage to the sensitive electronics in your projectors
no guarantee or refunds – you’re on your own to get a refund from the company when you buy from a reseller

Step 2: Know when to replace the projector lamp

You can expect up to 3000 hours with a new BenQ 65.J4002.001 projector lamp IF you buy from an authentic OEM from an authorized dealer.

Warning Messages

First warning: The BenQ 65.J4002.001 has been in operation for 1980 hours. If the projector is being run in Economic Mode you may continue until the second warning at 2980 hours at which time a second warning will appear.

Second warning : The BenQ PB8240 projector power will shutdown in 20 hours time. Replace the BenQ 65.J4002.001 lamp immediately.

Final warning: This message will flash in the screen’s center at 3000 hours and the Lamp Indicator will light up red for 40 seconds before the BenQ PB8240 projector shuts down. The projector will not turn on until the BenQ 65.J4002.001 lamp has been replaced.

Step 3: Replace the BenQ 65.J4002.001 projector lamp

Before changing the lamp:

Reduce the risk of electrical shock by disconnecting the power cord on the BenQ PB8240 projector.
Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

Turn the power off and disconnect the BenQ PB8240 projector.

The lamp cover is found on the bottom of the projector. Turn the projector over and loosen the two screws holding the BenQ PB8240 lamp cover in place. (Use a magnetic screwdriver to make the whole process easier.)

Loosen the screw on the BenQ 65.J4002.001 lamp.

Grab the wire handle on the BenQ 65.J4002.001 lamp so it lifts up. Slowly and gently pull theBenQ 59.J8101.CG1 lamp out of the projector. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
Avoid touching the optical components inside the projector as this can leave marks on the lenses causing image distortion and unwanted color changes.

Insert the new BenQ 65.J4002.001 lamp making sure the handle is fully locked. Tighten the screw. If the screw is too loose or too tight, the projector may not turn on.
Re-install the BenQ PB8240 lamp cover and tighten the screw.
Reset the total lamp operation timer.

NOTE: The BenQ 65.J4002.001 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Reset the projector lamp counter

It’s important to only reset the lamp timer when the BenQ 65.J4002.001 projector lamp has been replaced. Resetting the lamp timer without changing the BenQ 65.J4002.001 lamp can cause significant harm to your BenQ PB8240 projector.

Press and hold EXIT button on the projector for 3 seconds to display the total used lamp time.
Press MENU on either the projector or on the remote control. Scroll down to the LAMP HOUR TIMER. An adjustment message will appear.
Press MENU to reset the lamp hours.
Press EXIT.

Make your newly installed BenQ 65.J4002.001 projector lamp last longer with the following tips:

Keep your air filters clean to avoid overheating the projector.
Use the Lamp Power option on the BenQ PB8240 and set to Economic Mode to reduce the amount of power used but extend lamp life.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, BenQ 65.J4002.001 lamp, BenQ PB8240 projector, BenQ projector lamps, genuine lamps, replacement projector lamps

How to replace the BenQ PB8140 projector lamp

Shelagh McNallyPosted on October 23, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow our guide to replace the BenQ PB8140 projector lamp

You can expect up to 3000 hours of lamp life before the BenQ PB8140 projector lamp needs to be replace.

You’ll start to notice warning signs as the lamp starts to reach end of life.

Warning signs

Your first warning to replace the BenQ PB8140 projector lamp will show up when the lamp has been in operation for 1980 hours. If the projector is being run in Economic Mode you may continue until the second warning at 2980 hours at which time a second warning will appear.

The second warning will let you know that the power will shutdown in 20 hours time. Replace the BenQ PB8140 projector lamp immediately.

The final warning will flash in the center of the BenQ PB8140 screen at 3000 hours and the Lamp Indicator will light up red for 40 seconds before the BenQ PB8140 projector shuts down. The projector will not turn on until the lamp has been replaced.

Authentic lamps are important

Your BenQ PB8140 projector is a sophisticated machine with sensitive electronic components. The BenQ 65.J4002.001 projector lamp has been designed specifically to keep your projector operating at optimum levels. Generic “compatible” lamps are made with copycat technology that use inferior and often toxic materials.

Knock-off manufacturers don’t possess the proper technology to create these lamps and as a result these lamps have a shorter lamp life, are prone to explosions and can seriously damage your projector. Installing them cancels your warranty leaving your vulnerable should anything go wrong. It’s not worth the small savings. Protect yourself from buying a knock-off counterfeit compatible generic lamp.

You’ll need the BenQ 65.J4002.001 lamp model.

How to replace the BenQ PB8140 projector lamp

Before changing the lamp:

Reduce the risk of electrical shock by disconnecting the power cord on the BenQ PB8140 projector.
Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

Turn the power off and disconnect the BenQ PB8140 projector.
The lamp cover is found on the bottom of the projector. Turn the projector over and loosen the two screws holding the BenQ PB8140 lamp cover in place. (Use a magnetic screwdriver to make the whole process easier.)

Loosen the screw on the BenQ 65.J4002.001 lamp.

Grab the wire handle on the BenQ 65.J4002.001 lamp so it lifts up. Slowly and gently pull the BenQ 65.J4002.001 lamp out of the projector. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
Avoid touching the optical components inside the projector as this can leave marks on the lenses causing image distortion and unwanted color changes.

Insert the new BenQ 65.J4002.001 lamp making sure the handle is fully locked. Tighten the screw. If the screw is too loose or too tight, the projector may not turn on.
Re-install the BenQ PB8140 lamp cover and tighten the screw.
Reset the total lamp operation timer.

NOTE: The BenQ 65.J4002.001 lamp contains mercury and should not be thrown into regular garbage. It needs to be properly recycled.

Reset the lamp counter

It’s important to only reset the lamp timer when the BenQ 65.J4002.001 lamp has been replaced. Resetting the lamp timer without changing the BenQ 59.J8101.CG1 lamp can cause significant harm to your BenQ PB8140 projector.

Press and hold EXIT button on the projector for 3 seconds to display the total used lamp time.
Press MENU on either the projector or on the remote control. Scroll down to the LAMP HOUR TIMER. An adjustment message will appear.
Press MENU to reset the lamp hours.
Press EXIT.

Make your newly installed BenQ 65.J4002.001 lamp life last longer with the following tips:

Keep your air filters clean to avoid overheating the projector.
Use the Lamp Power option on the BenQ PB8140 and set to Economic Mode to reduce the amount of power used but extend lamp life.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, BenQ 65.J4002.001, BenQ PB8140 projector, genuine projector lamps

Install a new 4719-001997 DLP Chip to get rid of Samsung HLT5087SX/XAA white dots

Shelagh McNallyPosted on October 22, 2012 Posted in FixYourDLP, Rear Projection TV Lamp Replacement — No Comments ↓

White dots on your Samsung HLT5087SX/XAA? It’s time to replace the DLP Chip

Replace your 4719-001997 DLP Chip for under $300 and get rid of those white dots.

Note: These instructions can be used for the following Samsung models:

Find this New Mitsubishi/Toshiba 4719-001997 DLP Chip 1910-6143W on Amazon.

Equipment needed

- Electric Philips screwdriver
- needle nose pliers or a 5mm nut driver
- antistatic gloves OR plastic gloves used with an antistatic wrist band
- soft cloth or brush

Replacing the 4719-001997 DLP Chip

4719-001997 DLP Chip, Samsung HLT5087SX RPTV

Step 1

Step 1: Put on the plastic gloves. Loosen all the screws found on the back panel. Put the screws to one side and remove the back panel.

Step 2

Step 2: Loosen the two screws holding the lamp bracket in place.

Step 3

Step 3: Remove the 4 screws holding the lamp engine in place. Disconnect all the connectors. Important: don’t yank any cables.

Step 4

Step 4: Carefully remove light engine from the cabinet.

Step 5

Step 5: Remove the 2 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 6

Step 6: Carefully disconnect the cables between the terminal board and lamp.

Step 7

Step 7: Disconnect the clip connecting the cooling unit.

Step 8

Step 8: Remove the cooling unit and terminal board.

Step 9

Step 9: Remove the terminal board.

Step 10

Step 10: Loosen the 7 screws holding the terminal cover in place. (Good time to dust this section).

Step 11

Step 11: Carefully pop the terminal out of its holder.

Step 12

Step 12: Unlock the old DLP Chip from the terminal. You may need to use a flat edged screwdriver to pop it out.

Step 13

Step 13: Place the new DLP chip into place. Handle the DMD DLP CHIP only by the edges because it is very sensitive to static electricity.

Step 14

Step 14: Put the terminal back into its holder.

Step 15

Step 15: Tighten the 7 screws holding the terminal in place.

Step 16

Step 16: Replace the terminal board’s cover.

Step 17

Step 17: Reconnect the clip holding the cooling unit.

Step 18

Step 18: Re-connect the cables between the terminal board and lamp.

Step 19

Step 19: Tighten the 2 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 20

Step 20: Carefully replace the light engine back into the cabinet.

Step 21

Step 21: Replace and tighten the 4 screws holding the lamp engine in place. Re-connect all the connectors.

Step 22

Step 22: Put the light engine back into the RPTV. Tighten both screws that keep the back bracket in place.

Step 23

Step 23: Put the back panel back onto the TV. Put the screws back into place and tighten them. Enjoy the crisp, clear picture on your Samsung HLT5087SX/XAA RPTV.

Learn more about your Samsung HLT5087SX/XAA RPTV:
7 Tips for extending RPTV lamp life
RPTV Troubleshooting: TV won’t turn on
Consumer Alert: The dangers of RPTV generic lamps

Shop on Amazon for this chip.

Tagged with: 4719-001997 DLP Chip, affordable solution to white death problem, Samsung HLT5087SX, solving white death syndrome, troubleshooting, white death solution for Samsung

6 common projector problems after installing a new lamp

Shelagh McNallyPosted on October 20, 2012 Posted in Counterfeit Lamp Awareness, FixYourDLP, Projector Lamp Replacement Guides — 251 Comments ↓

Here are solutions to the six most common projector problems happening after installing a new projector lamp

Sometimes things don’t go as planned after installing a new projector lamp. Here are the solutions to the six most common projector problems.

Problem #1: My projector won’t turn on after I’ve installed my new lamp.

Solution: Check the power cord, lamp cover and lamp connections.

Before contacting customer service, be sure to first check that the projector power cord is plugged in and properly secured. Check the back lamp cover – if it’s loose the projector won’t turn on. If this doesn’t solve the problem, then open up the lamp cover and check the lamp connections. If the screws are too loose or too tight, the projector will not turn on.

Trade-in Amazon Fire tablets-Get 20% off a new Fire tablet

Problem #2: My projector is getting too hot after replacing the lamp

Solution: Clean your air filters and ventilation holes.

The main reason a projector starts to heat up is because the air filters or ventilation holes are clogged with dust or other debris. DLP projectors operate at high heat and most have one or more fans that blow air around the components to cool them off. A build up of dust prevents proper air circulation and can cause the projector to become very hot and the lamp to explode. When this happens, the projector temperature controls will go off. Always clean your filters after replacing the projector lamp. Use a can of compressed air and blow filters and ventilation holes dust free.

Shop Amazon Devices | All-new Fire HD 10 tablet

Problem #3: The picture is fine but the onscreen message says to replace the lamp even though it’s new!

Solution: You need to reset the lamp timer.

Your projector has a Lamp Timer or Lamp Hour Counter that automatically tracks lamp usage. It’s been designed to send you warning messages on screen and to trigger the Lamp Indicator when the projector lamp is approaching end of life. Many projectors will turn off automatically when the end of lamp hours has been reached – whether the lamp is new or not. Always reset your lamp timer after replacing the lamp. Check out our lamp replacements guides or your projector manual for instructions.

Introducing Echo Show 5

Problem #4: The picture is much dimmer.

Solution: Re-install the new bulb or replace the generic lamp previously installed.

This problem usually only happens when you have replaced only the bulb and not the entire housing. Check to make sure the bulb has been installed correctly. Purchasing a bare bulb is an economical option but you have to make sure it’s been installed properly. It should be flush with the front of the lamp housing cage and the new bulb should sit exactly in the same placement as the old bulb. If the new bulb is off center or not aligned properly your image will be dim. Removing the bulb and re-installing it more carefully should take care of a dim picture.

Kindle Unlimited Membership Plans

Problem #5: Projector turns on for a minute and then shuts off.

Solution: Clean the fans and filters. Replace the generic lamp.

Projectors will turn themselves off automatically if they detect any problems. Cleaning the projector of all dust and dirt will make the components work together in harmony. If dust is not the problem, then it’s the actual lamp. Have you installed a genuine OEM projector lamp? Generic, compatible lamps don’t operate properly in most projectors causing them to out of balance. This will make the projector shut down automatically. The solution for this problem is to replace the generic lamp with a genuine OEM lamp.

Shop Amazon Gift Cards. Any Occasion. No Expiration

Problem #6: The screen color is wrong and the picture is flickering.

Solution: Your color wheel may need to be replaced.

Usually the color is off with an older, dimmer lamp. However, since the projector lamp only has one color – white – the problem is usually with the internal optics. The color wheel or other optical components may have been damaged while the lamp was being replaced. Also installing generic lamps can damage the sophisticated and sensitive components such as the color wheel and DLP chip. The only solution for this problem is to contact a service rep.

Shop Amazon Basics – HDMI Cables

Save

Tagged with: DLP troubleshooting guide with new projector lamps, problems with new projector lamp, solve the DLP problem

When to replace the BenQ 60.J3503.CB1 projector lamp

Shelagh McNallyPosted on October 19, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Wondering which projectors are compatible with the BenQ 60.J3503.CB1 projector lamp? Keep reading!

If you’ve been using an authentic BenQ 60.J3503.CB1 projector lamp you can expect up to 3,000 hours of use before its reaches end of life and needs to be replaced.

Be sure to purchase an authentic BenQ 60.J3503.CB1 projector lamp to keep your BenQ projector working properly.

6 good reasons to avoid generics

generics have a shorter lamp life than original lamps
compatible are created with toxic materials and carcinogenic parts including Krypton-85
knock off lamps are prone to explosions
generic lamps damage the sensitive electronics in your projectors
when you buy copy-cat lamps you get no guarantee or refunds
installing a generic lamp voids your projector’s warranty.

Save yourself unnecessary headaches and buy an authentic BenQ 60.J3503.CB1 lamp from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Compatible Projectors

For step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp, scroll down and click on your BenQ model.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7000/7100 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7105/7110 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7200/7205 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7210 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7220/7225 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7230/PE8250 projector.

Extending the life of the BenQ 60.J3503.CB1 lamp:

Keep your air filters clean to avoid overheating the projector.
Use the Lamp Power option on the BenQ projector and set to Economic Mode to reduce the amount of power used but extend lamp life.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, BenQ 60.J3503.CB1 projector lamp, BenQ PB7000 projector, BenQ PB7105 projector, BenQ PB7110 projector, BenQ PB7200 projector, BenQ PB7205 projector, BenQ PB7210 projector, BenQ PB7220 projector, BenQ PB7225 projector, BenQ PB7230 projector, BenQ PE8250 projector, BenQ projector lamps, genuine lamps, genuine projector lamps, Lamp replacement, replacement projector lamps

Are white dots on your Samsung HLT5689SX/XAA ruining your picture? Replace the DLP Chip

Equipment needed

Replacing the 4719-001997 DLP Chip

Learn more about your Samsung HLT5689SX/XAA RPTV.:

Only a few companies sell authentic projector lamps. Make sure you’re buying from a recognized authorized dealer.

DLP lamps sophisticated technology

Not all lamps are equal

Look for the seal of approval

6 good reasons to avoid generics

Learn the 7 Ways to spot a counterfeit lamp.

Are white dots ruining the picture on your Samsung HLT5687SX/XAA picture?

Equipment needed

Replacing the 4719-001997 DLP Chip

Learn more about your Samsung HLT5687SX/XAA RPTV:

You can expect up to 2000 hours of life when you install an authentic BenQ 65.J4002.001 lamp.

Finding the correct lamp

6 good reasons to avoid generics

Compatible Projectors

The BenQ 65.J4002.001 is compatible with:

For step-by-step instructions on replacing your BenQ 65.J4002.001 projector lamp, click on your projector listed below:

Click here for step-by-step instructions on how to change the BenQ 65.J4002.001 projector lamp for the BenQ PB8140 projector.

Click here for step-by-step instructions on how to change the BenQ 65.J4002.001 projector lamp for the BenQ PB8240 projector.

Eliminate dots on your Samsung HLT5676SX/XAA by replacing the 4719-001997 DLP Chip

Equipment needed

Replacing the 4719-001997 DLP Chip

Learn more about your Samsung HLT5676SX/XAA RPTV:

Follow our guide to replace the BenQ 65.J4002.001 projector lamp in your BenQ PB8240 projector in 3 easy steps.

Step 1: Be prepared — buy an authentic projector lamp

Step 2: Know when to replace the projector lamp

Step 3: Replace the BenQ 65.J4002.001 projector lamp

Reset the projector lamp counter

Follow our guide to replace the BenQ PB8140 projector lamp

Warning signs

Authentic lamps are important

How to replace the BenQ PB8140 projector lamp

Reset the lamp counter

Make your newly installed BenQ 65.J4002.001 lamp life last longer with the following tips:

White dots on your Samsung HLT5087SX/XAA? It’s time to replace the DLP Chip

Equipment needed

Replacing the 4719-001997 DLP Chip

Here are solutions to the six most common projector problems happening after installing a new projector lamp

Problem #1: My projector won’t turn on after I’ve installed my new lamp.

Solution: Check the power cord, lamp cover and lamp connections.

Problem #2: My projector is getting too hot after replacing the lamp

Solution: Clean your air filters and ventilation holes.

Problem #3: The picture is fine but the onscreen message says to replace the lamp even though it’s new!

Solution: You need to reset the lamp timer.

Problem #4: The picture is much dimmer.

Solution: Re-install the new bulb or replace the generic lamp previously installed.

Problem #5: Projector turns on for a minute and then shuts off.

Solution: Clean the fans and filters. Replace the generic lamp.

Problem #6: The screen color is wrong and the picture is flickering.

Solution: Your color wheel may need to be replaced.

Wondering which projectors are compatible with the BenQ 60.J3503.CB1 projector lamp? Keep reading!

6 good reasons to avoid generics

Compatible Projectors

The BenQ 5J.00S01.001 is compatible with:

For step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp, scroll down and click on your BenQ model.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7000/7100 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7105/7110 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7200/7205 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7210 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7220/7225 projector.

Click here for step-by-step instructions on how to change the BenQ 60.J3503.CB1 projector lamp for the BenQ PB7230/PE8250 projector.

Extending the life of the BenQ 60.J3503.CB1 lamp: