We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 118

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
DP-6155 XGA projector, ASK Proxima LAMP-031

DP-6155 XGA projector

The projector lamp for the ASK DP-6155 XGA projector lamp will run for approximately 1500-2000 hours before needing to be replaced.

When the ASK Proxima LAMP-031 lamp is approaching end of life the ALARM indicator will light up red.

Buying the right lamp

The correct lamp to use is the ASK Proxima LAMP-031. Be sure to install a genuine ASK Proxima LAMP-031 and avoid generic knock-off lamps. Even though they appear to be a bargain, these so-called “compatible” can end up costing more in the long run. These lamps are prone to explosion and have been created using the carcinogenic substance Krypton-85.

Using a counterfeit generic lamp can damage the sensitive components since these knock-off lamps have not been created with the correct components and can cause malfunction. The light provided by these lamps is also substandard with poor illumination.

Installing a generic lamp will also void any warranty for your ASK DP-6155 XGA projector. Go with an authentic ASK Proxima LAMP-031 OEM lamp sold by a dependable seller. Learn the 7 Ways to spot a counterfeit lamp.

Replacing the ASK Proxima LAMP-031 lamp

DP-6155 XGAlamp cover, ASK Proxima LAMP-0311. Disconnect the power cord and allow the projector to cool for one hour before replacing the lamp. The ASK DP-6105 XGA operates under high heat and can cause burns.

2. The lamp lid for the ASK DP-6105 XGA is found on the bottom of the projector. Be sure to protect the top of the projector before turning it over to access the ASK DP-6105 XGA lamp. DP-6105 XGA lamp, ASK Proxima LAMP-031

3. Unscrew the three safety screws holding the ASK Proxima LAMP-031 lamp holder in place.

4. Gently grab the lamp holder and pull the ASK Proxima LAMP-031 out of the projector. Be sure to dispose of the used ASK Proxima LAMP-031 lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.

5. Inset the new ASK Proxima LAMP-031 lamp all the way into the ASK DP-6105 XGA unit. Tighten the three screws that hold the ASK Proxima LAMP-031 lamp in place. You’re now ready to reset the lamp timer.

Reset the lamp timer

In order for the ASK DP-6155 XGA to correctly track the lamp life of your newly installed ASK Proxima LAMP-031 lamp, you’ll need to reset the

DP-6105 XGA lamp reset menu, ASK Proxima LAMP-031 DP-6105 XGA lamp reset icon, ASK Proxima LAMP-03
Reset the lamp timer:

  • Open the MENU system.
  • Scroll down to BASIC. Press ENTER.
  • Scroll down to ADVANCED. Press ENTER.
  • Scroll down to SERVICE. Click on LAMP TIMER RESET. Click on YES.

 

 

 

Tagged with: , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
DP-6105 XGA projector, ASK Proxima LAMP-031

DP-6105 XGA projector

Replacing the ASK DP-6105 XGA projector lamp is quick and easy. Follow out this guide to a new ASK Proxima LAMP-031 for your ASK DP-6105 XGA projector.

Lamp Replacement Warnings

DP-6105 XGA Lamp Alarm, ASK Proxima LAMP-031

Lamp alarm

When it’s time to replace the ASK Proxima LAMP-031 you’ll notice a the ALARM button has light up read. Replace the lamp immediately to avoid any risk of the lamp exploding for overheating or the projector suddenly shutting down.

Go with authentic lamps

It’s important to install the correct ASK Proxima LAMP-031 lamp. Educate yourself and learn how to spot a counterfeit lamp. Generic lamps often advertised as “compatible” should be avoided since they can be dangerous. They’re manufactured with inferior parts using toxic substances such as Krypton-85, which has been linked to cancer.

These counterfeit generic lamp compromise your health and safety while voiding any warranties with your ASK DP-6105 XGA projector. Invest in a genuine OEM lamp with proper components that will keep the ASK DP-6105 XGA projector projector is working at its peak. Go with authentic.

Replacing the ASK Proxima LAMP-031 lamp

DP-6105 XGA lamp cover, ASK Proxima LAMP-0311. Disconnect the power cord and allow the projector to cool for one hour before replacing the lamp. The ASK DP-6105 XGA operates under high heat and can cause burns.

2. The lamp lid for the ASK DP-6105 XGA is found on the bottom of the projector. Be sure to protect the top of the projector before turning it over to access the ASK DP-6105 XGA lamp. DP-6105 XGA lamp, ASK Proxima LAMP-031

3. Unscrew the three safety screws holding the ASK Proxima LAMP-031 lamp holder in place.

4. Gently grab the lamp holder and pull the ASK Proxima LAMP-031 out of the projector. Be sure to dispose of the used ASK Proxima LAMP-031 lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.

5. Inset the new ASK Proxima LAMP-031 lamp all the way into the ASK DP-6105 XGA unit. Tighten the three screws that hold the ASK Proxima LAMP-031 lamp in place. You’re now ready to reset the lamp timer.

Reset the lamp timer

In order for the ASK DP-6105 XGA to correctly track the lamp life of your newly installed ASK Proxima LAMP-031 lamp, you’ll need to reset the timer.

To reset the lamp timer:

  • Open the MENU system.
  • Scroll down to BASIC. Press ENTER.
  • Scroll down to ADVANCED. Press ENTER.
  • Scroll down to SERVICE.
  • Click on LAMP TIMER RESET.
  • Click on YES.

DP-6105 XGA, lamp reset menu, ASK Proxima LAMP-031DP-6105 XGA lamp reset icon, ASK LAMP-026

 

 

 

 

 

 

 

 

 

Tagged with: , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP — No Comments ↓
DP-5155 SVGA projector, ASK Proxima LAMP-031

DP-5155 SVGA projector

Change your ASK Proxima LAMP-031 in 3 easy steps by following our step-by-step guide.

Step 1: Finding the correct ASK Proxima LAMP-031

You’ll need to purchase an authentic ASK Proxima LAMP-031 from an authorized dealer.  Beware of cheaper knock-off lamps as they will damage the sensitive mechanisms in your DP-5155 SVGA projector. Although sold at discount prices, these generic “compatible” lamps have a much shorter life span due to their inferior materials and worksmanship. They are prone to explosions and contain cancer-causing materials, such as Krypton 85. Installing a knock-off lamp into your DP-5155 SVGA projector will also void your warranty.

Protect your health and keep your projector working properly — install an authentic ASK Proxima LAMP-031!

 STEP 2: Replacing the ASK Proxima LAMP-031 projector lamp

DP-5155 SVGA Lamp Alarm, ASK Proxima LAMP-031

Lamp alarm

DP-5155 SVGA warning message, ASK Proxima LAMP-031

When it’s time to replace the ASK Proxima LAMP-031 for your DP-5155 SVGA projector, you’ll see the ALARM button on the projector light up red. A warning message will also appear on screen.

 

DP-5155 SVGA Lamp, ASK Proxima LAMP-031

Step-by-step instructions for replacing the ASK Proxima LAMP-031:

  • Turn off the projector and unplug the AC cord. These projectors operate under high temperatures and there is a risk of burning if the projector has not cooled enough. Allow the DP-5155 SVGA projector to cool for one hour.
  • The Lamp Cover for the DP-5155 SVGA projector is on the bottom of the projector. Gently turn it over and loosen the 3 screws holding the lamp in place.
  • Grab the handle on the ASK Proxima LAMP-031 lamp cage and gently lift out the lamp. Place to one side.

  • Don’t throw this lamp into the regular garbage as it contains mercury — send it to a local recycling program where it can be disposed of properly.

DP-5155 SVGA, ASK Proxima LAMP-031

  • Take the new ASK Proxima LAMP-031 lamp. Avoid touching the bare bulb; the oil on your finger can leave a black mark on the lamp affecting the projected image. Place it into the DP-5155 SVGA projector.
  • Tighten the two screws on the new ASK Proxima LAMP-031 lamp.
  • Put the lid back on. Tight the screw holding the lid in place.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK Proxima LAMP-031 in the DP-5155 SVGA projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

DP-5155 SVGA reset lamp menu, ASK Proxima LAMP-031DP-5155 SVGA reset lamp menu, ASK Proxima LAMP-031

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option.
  • Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.

 

Tagged with: , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — 2 Comments ↓
C105/C95 XGA warning message, ASK Proxima LAMP-031

Lamp replacement alarm

Follow our quick and easy step guide to installing a new ASK Proxima LAMP-031 projector lamp for your ASK DP-6150 projector.

Finding the correct lamp

C105/C95 XGA projector, ASK Proxima LAMP-031

C105/C95 XGA projector

Watch for the warning messages on the ASK C105/C95 XGA projector screen as well as the ALARM on the projector light red. Either of these messages are indicators that the ASK Proxima LAMP-031 for your ASK C105/C95 XGA projector must be replaced immediately.

Buy genuine lamps

Be safe and get the best lamp for your ASK C105/C95 XGA projector. Buy an authentic lamp from an authorized dealer that guarantees the ASK Proxima LAMP-031 you are installing will work in harmony with your projector. These genuine ASK Proxima LAMP-026 lamps have been manufactured with the correct materials and are designed to work properly with the intricate components in your ASK C105/C95 XGA projector.

While the cheaper knock-off lamps sold at discount prices appear to be a smart bargain, they actually pose a danger to your health. Copy-cat manufacturers create these lamps are using toxic materials such as the cancer-causing compound Krypton 85 to get the same results since they don’t have access to the proper compounds. When these generic “compatible” lamps break or explode from overheating, anyone near the projector is exposed people to these toxic materials inside the lamp. Many generic lamps are also created without the proper safety device to protect your eyesight from UV light.Installing them also voids your projector warranty.

Protect your health and keep your projector warranty valid — buy an authentic ASK Proxima LAMP-026.

STEP 2: Replacing the ASK Proxima LAMP-031 projector lamp

IMPORTANT: Allow the ASK DP-6150 projector to fully cool down for at least one hour before replacing the ASK Proxima LAMP-031. These projectors operate under high heat and there is a seriousrisk of burning if the projector is not cooled enough.

C105/C95 XGA, ASK Proxima LAMP-031To install a new ASK Proxima LAMP-031 lamp:

  • Gently turn over the ASK DP-6150 projector to access the lamp cage.
  • Loosen the 3 screws holding the ASK Proxima LAMP-031 lamp in place.
  • Grab the handle on the ASK Proxima LAMP-031 lamp cage and gently lift out the lamp. Place to one side.
  • IMPORTANT: These lamps contain mercury and must go to a local recycling program for proper disposal. Don’t throw used ASK LAMP-026 lamps into regular garbage! C105/C95 XGA, ASK Proxima LAMP-031
  • Take the new ASK Proxima LAMP-031 lamp. Don’t touch the bare bulb since the oil on your finger will burn a black mark on the lamp when the projector is turn on.
  • Place the ASK Proxima LAMP-031 into the projector.
  • Tighten the three screws on the new ASK Proxima LAMP-031 lamp.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK Proxima LAMP-031 in the ASK DP-6150 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.C105/C95 XGA, ASK Proxima LAMP-031

C105/C95 XGA lamp reset menu, ASK Proxima LAMP-031To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
C85 SVGA projector, ASK Proxima LAMP-031

C85 SVGA projector

Replacing the ASK Proxima LAMP-031 projector lamp in your ASK C85 projector in three easy steps

Step 1: Finding the correct lamp

Wondering when to replace the ASK Proxima LAMP-031? Watch for the ALARM button on the projector light red. Watch for the warning screen as well.

C85 SVGA warning message, ASK Proxima LAMP-031

Lamp alarm

C85 SVGA warning message, ASK Proxima LAMP-031

Lamp warning screen

 

 

When it’s time to replace the ASK Proxima LAMP-031 for your ASK C85 SVGA projector, you’ll see the ALARM button on the projector light up red. A lamp warning message will also appear on screen.

Go with authentic

Beware of cheaper knock-off lamps sold at discount prices. They appear to be a great bargain but will actually cost more money in the long run. These lamps have a shorter life span and will damage your projector. The copy-cat manufacturers creating these lamps don’t have the same safety concerns are and using toxic materials such as the cancer-causing compound Krypton 85 to manufacture their inferior lamps.

These generic “compatible” lamps are prone to breaking or exploding from overheating, exposing people to these toxic materials inside the lamp. Installing them also voids your projector warranty.

You’ll get the best lamp for your ASK C85 SVGA projector when you buy from an authorized dealer. An ASK Proxima LAMP-031 manufactured by an OEM company use the correct materials and are designed to work properly with the intricate components in your ASK C85 SVGA projector.

Protect your health and keep your projector warranty valid — buy an authentic ASK Proxima LAMP-031.

 STEP 2: Replacing the ASK Proxima LAMP-031 projector lamp

IMPORTANT: Before replacing the ASK Proxima LAMP-031 allow the ASK DP-6100 projector to fully cool down for at least one hour. These projectors operate under high heat and there is a seriousrisk of burning if the projector is not cooled enough.

C85 SVGA lamp cage, ASK Proxima LAMP-031To install a new ASK Proxima LAMP-031 lamp:

  • Gently turn over the ASK C85 SVGA projector to access the lamp cage.
  • Loosen the 3 screws holding the ASK Proxima LAMP-031 lamp in place.
  • Grab the handle on the ASK Proxima LAMP-031 lamp cage and gently lift out the lamp. Place to one side.
  • IMPORTANT: These lamps contain mercury and should be sent to a local recycling program for proper disposal. Don’t throw into regular garbage.

ASK DP-6100 lamp replacement, ASK LAMP-026

  • Take the new ASK Proxima LAMP-031 lamp. Don’t touch the bare bulb since the oil on your finger will burn a black mark on the lamp when the projector is turn on. This will cause a black spot on the screen and affect the projected image.
  • Place the ASK Proxima LAMP-031into the projector.
  • Tighten the three screws on the new ASK Proxima LAMP-031 lamp.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK LAMP-026 in the DP-6100 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

 

C85 SVGA reset menu for ASK Proxima LAMP-031C85 SVGA reset icon for ASK Proxima LAMP-031To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER. The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

ASK Proxima LAMP-026

The ASK Proxima LAMP-026 lamp should have a life that lasts between 1500 -2000 hours before needing to be replaced. When it’s reaching its end of life, The Lamp Replacement Indicator on the projector’s panel will light up orange.

Also install a genuine ASK Proxima LAMP-026 from a recognized OEM manufacturer. Generic/knockoff/compatible lamps can damage the sensitive (and expensive) mechanisms in your projector. They give poor illumination and are prone to explosions, which may expose you and your audience to the carcinogenic substance Krypton-85 used in the making of these counterfeit lamps.

Installing a generic lamp will also void any warranty for your ASK Proxima projectors. Go with an authentic ASK Proxima LAMP-026. Learn the 7 Ways to spot a counterfeit lamp.

Compatible Projectors

The ASK Proxima LAMP-026 is compatible with the following projectors:

ASK C20 SVGA

ASK C60 XGA

ASK C80

ASK C100/C90

ASK DP-6100

ASK DP-6150

 

For step-by-step instructions on replacing your ASK Proxima LAMP-026 projector lamp, click on your projector listed below:

ASK C20 SVGA projector, ASK Proxima Lamp-026

ASK C20 SVGA projector

Click here for step-by-step instructions on how to change the ASK Proxima LAMP-026 projector lamp for the ASK C20 SVGA projector.

 

 

 

 

 

ASK C60 XGA projector, ASK Proxima Lamp-026

ASK C60 XGA projecto

Click here for step-by-step instructions on how to change the ASK Proxima LAMP-026 projector lamp for the ASK C60 XGA projector.

 

 

 

 

 

ASK C80 projector, ASK LAMP-026

ASK C80 projector

 

 

 

Click here for step-by-step instructions on how to change the ASK Proxima LAMP-026 projector lamp for the ASK C80 projector.

 

 

 

ASK C100 projector, ASK LAMP-026

ASK C100 projector

Click here for step-by-step instructions on how to change the ASK Proxima LAMP-026 projector lamp for the ASK C100/C90 projector.

 

 

 

 

 

ASK DP-6150 projector, ASK Proxima LAMP-026

ASK DP-6100 projector

Click here for step-by-step instructions on how to change the ASK Proxima LAMP-026 projector lamp for the ASK DP-6100 projector.

 

 

 

 

 

ASK DP-6150 projector, ASK Proxima LAMP-026

ASK DP-6150 projector

 

 

Click here for step-by-step instructions on how to change the ASK Proxima LAMP-026 projector lamp for the ASK DP-6150 projector.

 

 

 

 

 

 

 

Tagged with: , , , , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK DP-6150 projector, ASK Proxima LAMP-026

ASK DP-6150 projector

Follow our quick and easy step guide to installing a new ASK Proxima LAMP-026 projector lamp for your ASK DP-6150 projector.

Step 1: Finding the correct lamp

ASK DP-6150 lamp warning message, ASK LAMP-026

Lamp warning screen

ASK DP-6100 lamp replacement alarm, ASK LAMP-026

Lamp alarm

 

 

 

 

Watch for the warning messages on the ASK DP-6150 projector screen as well as the ALARM on the projector light red. Either of these messages are indicators that the ASK LAMP-026 for your ASK DP-6150 projector must be replaced immediately.

Go with a genuine ASK LAMP-026 lamp

Be safe and get the best lamp for your ASK DP-6150 projector. Buy an authentic lamp from an authorized dealer that guarantees the ASK Proxima LAMP-026 you are installing will work in harmony with your projector. These genuine ASK Proxima LAMP-026 lamps have been manufactured with the correct materials and are designed to work properly with the intricate components in your ASK DP-6150 projector.

While the cheaper knock-off lamps sold at discount prices appear to be a smart bargain, they actually pose a danger to your health. Copy-cat manufacturers create these lamps are using toxic materials such as the cancer-causing compound Krypton 85 to get the same results since they don’t have access to the proper compounds. When these generic “compatible” lamps break or explode from overheating, anyone near the projector is exposed people to these toxic materials inside the lamp. Many generic lamps are also created without the proper safety device to protect your eyesight from UV light.Installing them also voids your projector warranty.

Protect your health and keep your projector warranty valid — buy an authentic ASK Proxima LAMP-026.

STEP 2: Replacing the ASK LAMP-026 projector lamp

IMPORTANT: Allow the ASK DP-6150 projector to fully cool down for at least one hour before replacing the ASK LAMP-026. These projectors operate under high heat and there is a seriousrisk of burning if the projector is not cooled enough.

ASK DP-6150 lamp cover, ASK LAMP-026To install a new ASK Proxima LAMP-026 lamp:

  • Gently turn over the ASK DP-6150 projector to access the lamp cage.
  • Loosen the 3 screws holding the ASK Proxima LAMP-026 lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.
  • IMPORTANT: These lamps contain mercury and must go to a local recycling program for proper disposal. Don’t throw used ASK LAMP-026 lamps into regular garbage! ASK DP-6150 lamp replacement, ASK LAMP-026
  • Take the new ASK Proxima LAMP-026 lamp. Don’t touch the bare bulb since the oil on your finger will burn a black mark on the lamp when the projector is turn on.
  • Place the ASK Proxima LAMP-026 into the projector.
  • Tighten the three screws on the new ASK Proxima LAMP-026 lamp.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK Proxima LAMP-026 in the ASK DP-6150 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK DP-6150 lamp reset menu, ASK LAMP-026ASK DP-6150 replace lamp icon, ASK LAMP-026

 

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK DP-6100, ASK LAMP-026

ASK DP-6100 projector

Follow our 3 step guide to a new ASK Proxima LAMP-026 projector lamp for your ASK DP-6100 projector.

Step 1: Finding the correct lamp

 

ASK DP-6100 lamp replacement alarm, ASK LAMP-026

Lamp alarm

ASK DP-6100 lamp warning message, ASK LAMP-026

Lamp warning screen

 

 

 

 

 

When it’s time to replace the ASK Proxima LAMP-026 for your ASK DP-6100 projector, you’ll see the ALARM button on the projector light up red. A lamp warning message will also appear on screen.

Go with authentic

You’ll get the best lamp for your ASK DP-6100 projector when you buy from an authorized dealer. An ASK Proxima LAMP-026 manufactured by an OEM company use the correct materials and are designed to work properly with the intricate components in your ASK DP-6100 projector.

Beware of cheaper knock-off lamps sold at discount prices. They appear to be a great bargain but will actually cost more money in the long run. These lamps have a shorter life span and will damage your projector. The copy-cat manufacturers creating these lamps don’t have the same safety concerns are and using toxic materials such as the cancer-causing compound Krypton 85 to manufacture their inferior lamps.  These generic “compatible” lamps are prone to breaking or exploding from overheating, exposing people to these toxic materials inside the lamp. Installing them also voids your projector warranty.

Protect your health and keep your projector warranty valid — buy an authentic ASK Proxima LAMP-026 .

 STEP 2: Replacing the ASK LAMP-026 projector lamp

IMPORTANT: Before replacing the ASK Proxima LAMP-026 allow the ASK DP-6100 projector to fully cool down for at least one hour. These projectors operate under high heat and there is a seriousrisk of burning if the projector is not cooled enough.

ASK DP-6100 lamp cover, ASK LAMP-026To install a new ASK LAMP-026 lamp:

  • Gently turn over the ASK DP-6100 projector to access the lamp cage.
  • Loosen the 3 screws holding the ASK Proxima LAMP-026 lamp in place.
  • Grab the handle on the ASK LAMP-026 lamp cage and gently lift out the lamp. Place to one side.
  • IMPORTANT: These lamps contain mercury and should be sent to a local recycling program for proper disposal. Don’t throw into regular garbage!

 

ASK DP-6100 lamp replacement, ASK LAMP-026

  • Take the new ASK Proxima LAMP-026 lamp. Don’t touch the bare bulb since the oil on your finger will burn a black mark on the lamp when the projector is turn on. This will cause a black spot on the screen and affect the projected image.
  • Place the ASK LAMP-026 into the projector.
  • Tighten the three screws on the new ASK Proxima LAMP-026 lamp.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK LAMP-026 in the DP-6100 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK DP-6100 lamp reset menu, ASK LAMP-026ASK C100/C90 lamp reset icon, ASK LAMP-026

 

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK C60 XGA, projector, ASK-026 lamp

ASK C60 XGA, projector,

ASK C60 XGA, projector alarm, ASK 26 lamp

Projector Alarm

When it’s time to replace the ASK Proxima LAMP-026 for your ASK C60 XGA projector, you’ll see the ALARM button on the projector light  red.  A warning message will also appear on screen.

Replace the ASK Proxima LAMP-026 in the ASK C60 XGA projector in 3 easy steps by following our step-by-step guide.

STEP 1: Buying the correct lamp

It’s important to purchase your ASK Proxima LAMP-026from an authorized dealer and get the best lamp for your ASK C20 SVGA projector.  There are plenty of “bargain” generic lamps being sold that claim to be the same as an authentic ASK LAMP-026 lamp.

Beware of these cheaper knock-off lamps as they often turn out to be more expensive in the long run. Not only do they have a much shorter life, they produce a poor quality picture and since they are not fitted properly usually damage the sensitive mechanisms in your ASK C60 XGA projector.

ASK LAMP-026Even more disturbing: Copy-cat manufacturers are using carcinogenic Krypton 85 to get the same performance as authentic lamps. Since these poor quality lamps are prone to explosions and breakage, consumers are being exposed to this toxic substance. Learn how to protect yourself against dangerous counterfeit lamps. Keep yourself and your projector safe by installing an authentic ASK Proxima LAMP-026 from a recognized reseller.

STEP 2: Install the ASK LAMP-026

There is a risk of burning yourself if you try to replace the ASK LAMP-026 before the ASK C60 XGA projector has cooled down sufficiently. Wait until the projector is cool to the touch before changing any lamps. Before starting the installation be sure unplug the AC cord.ASK C60 XGA lamp cover, ASK 26 lamp

  • To access the lamp, turn over the ASK C60 XGA projector.
  • Loosen the 3 screws holding the lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.

  • ASK LAMP-026 lamps contains mercury and should sent to a local recycling program for proper disposal. Do not place into regular garbage.

ASK C60 XGA lamp cover, ASK 26 lamp

  • Take the new ASK Proxima LAMP-026 lamp. Don’t touch the bare bulb–the oil on your fingers can leave a black mark on the lamp affecting the projected image. Place the ASK Proxima LAMP-026into the projector.
  • Tighten the three screws on the new ASK LAMP-026 lamp.
  • You are ready to reset the Lamptimer.

 

 

 

 

STEP 3: Reset the Lamptimer

In order to properly track the lamp life of the newly installed ASK Proxima LAMP-026 in the ASK C60 XGA projector,  you must reset the Lamptimer. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK ASK C60 lamp reset menu, ASK LAMP-026ASK C60 XGA lamp reset icon, ASK LAMP-026

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK C20 SVGA projector, ASK 26 lamp

ASK C20 SVGA projector

ASK C20 SVGA projector alarm, ASK 26 lamp

The lamp in the ASK C20 SVGA projector has a life of between 1500 to 2000 hours. When it’s time to replace the ASK Proxima LAMP-026 for your ASK C20 SVGA projector, you’ll see the ALARM button on the projector light  red. A warning message will also appear on screen.

Follow our step-by-step guide for a quick and easy replacement of the ASK Proxima LAMP-026 in the ASK C20 SVGA projector.

Go with an authentic ASK LAMP-026

Protect your health and keep your projector warranty valid — install an authentic ASK LAMP-026.

Buy an ASK Proxima LAMP-026 from an authorized dealer and get the best lamp for your ASK C20 SVGA projector.  Beware of cheaper knock-off lamps that will damage the sensitive mechanisms in your ASK C20 SVGA projector. These counterfeit “compatible” lamps are often sold at discounted prices and may appear to be a  good deal but actually have a much shorter life span.

Due to their inferior materials and worksmanship, they are prone to exploding when installed into the projector. Copy-cat manufacturers are also using Krypton 85, a carcinogenic, radioactive material to create these generic “compatible” lamps.

Keep yourself and your projector safe by installing an authentic ASK Proxima LAMP-026 from a recgonized reseller.

How to install the ASK LAMP-026

Before starting turn off the projector and unplug the AC cord. Allow the ASK C20 SVGA projector to cool for one hour. There is a risk of burning yourself if you try to replace the ASK Proxima LAMP-026 before the projector has cooled down sufficiently.

ASK C20 SVGA lamp cover, ASK 26 lamp

  • Turn over the ASK C20 SVGA to access the lamp. Loosen the 3 screws holding the lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.

  • The ASK LAMP-026 lamp contains mercury and should sent to a local recycling program for proper disposal.

ASK C20 SVGA lamp cover, ASK 26 lamp

 

  • Take the new ASK Proxima LAMP-026 lamp. Avoid touching the bare bulb with as the oil on your finger can leave a black mark on the lamp affecting the projected image. Place it into the projector.
  • You are ready to reset the Lamptimer.

 

 

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK Proxima LAMP-026 in the ASK C20 SVGA projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK C20 SVGA,, ASK LAMP-026ASK C20 SVGA lamp reset icon, ASK LAMP-026

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group