About Us - Page 133 of 171 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

How to Change the Lamp in a Sanyo PLC-XW10 Projector

Shelagh McNallyPosted on March 21, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XW10 Projector

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XW10 LAMP REPLACEMENT

When the image on your Sanyo PLC-XW10 projector becomes extremely dark or an unnatural colour, it’s time to change the projector lamp. You’ll notice that Lamp Replacement Indicator on the top control panel will turn yellow.

The lifespan of your Sanyo PLC-XW10 projector lamp will vary depending on how much the projector is used and if the air filters are cleaned regularly.

You’ll need to install a new Sanyo POA-LMP31 (service parts no 610 289 8422) projector lamp.

Before installation:

Buy your Sanyo POA-LMP31 (610 289 8422) from an authorized manufacturer and avoid the lower-priced knock-off lamps. These knock-off lamps are usually made with counterfeit parts that are inferior and can damage the sensitive mechanisms in your Sanyo PLC-SW15 projector. They may end up costing you more if they damage your projector since they also void your waranty. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee that the lamp you are installing is suitable for your projector.

Replacing the Sanyo POA-LMP31 Lamp Assembly

1. Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XW10 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

2. The lamp cover for the Sanyo PLC-XW10 is located at the bottom of the projector. Gently turn the projector over and loosen the screw holding the lamp cover. Remove the cover and put it to one side.

3. Inside you’ll find the S Sanyo POA-LMP31 (service parts no 610 289 8422) lamp cage. Loosen both screws holding the lamp cage in place. Grab the handle on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose the used lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP31 (610 289 8422) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP31 (6102898422) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XW10 projector will not turn on. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XW10. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Control mode found on the Setting menu.

NOTE: Be sure to properly recycle your used Sanyo POA-LMP31 (service parts no 610 289 8422) lamps. Since they contain mercury they can’t be placed into regular garbage.

Reset the Lamp Replacement Monitor Timer by following the instructions below.

How to reset the Sanyo PLC-XW10 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the monitor not tracking the Sanyo POA-LMP31 (service parts no 610 289 8422) lamp life properly.

Turn the Sanyo PLC-XW10 projector on.
Press the MENU button to access the ON-SCREEN MENU.
Press the POINT LEFT/RIGHT button to select the SETTING menu.
Press the SELECT button to open the SETTING MENU option.
Press the POINT DOWN button so the red-arrow appears.
Move down to the LAMP AGE option. Press SELECT to open the next option.
The message “Lamp replace monitor Reset?” will be displayed.
Click on the option YES to reset the timer.
RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

Extend the life of the Sanyo POA-LMP31 lamp

Extend the life of your newly installed Sanyo POA-LMP31 (service parts no 610 289 8422) by following these tips:

Wait at least five minutes before turning the Sanyo PLC-XW10 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP31 (service parts no 610 289 8422) and prevent the Sanyo PLC-XW10 from overheating.

Tagged with: authentic lamps, genuine lamps, Lamp replacement, philips, Projector LAMP, samsung, Sanyo PLC-XW10, Sanyo POA-LMP23, Sanyo POA-LMP3, Sanyo POA-LMP31 (service parts no 610 289 8422)

Replace your Sanyo PLC-SW15 projector lamp in 6 easy steps

Shelagh McNallyPosted on March 21, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-SW15 projector

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-SW15 LAMP REPLACEMENT

The lifespan of your Sanyo PLC-SW15 projector lamp will vary depending on how much the projector is used and if the air filters are cleaned regularly.

When your lamp is nearing its end of life you’ll see the Lamp Replace Indicator on the top of the projector flashing yellow. This is your signal that it’s time to install a new Sanyo POA-LMP23 (service parts no 610 285 2912) projector lamp.

Before installation:

Buy your Sanyo POA-LMP23 (610 285 2912) from an authorized manufacturer and avoid the lower-priced knock-off lamps. These knock-off lamps are usually made with counterfeit parts that are inferior and can damage the sensitive mechanisms in your Sanyo PLC-SW15 projector. They may end up costing you more if they damage your projector since they also void your warranty. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee that the lamp you are installing is suitable for your projector.

Replacing the Sanyo POA-LMP23 Lamp Assembly

1. Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-SW15 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

2. The lamp cover for the Sanyo PLC-SW15 is located at the bottom of the projector. Gently turn the projector over and loosen the screw holding the lamp cover in place. Remove the cover and put it to one side.

3. Inside you’ll find the Sanyo POA-LMP23 (service parts no 610 285 2912) lamp cage. Loosen both screws holding the lamp cage in place. Grab the handle on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose the used lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP23 (6102852912) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP23 (610 285 2912) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SW15 projector will not turn on. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-SW15. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Replacement Monitor Timer by following the instructions below.

NOTE: Be sure to properly recycle your used Sanyo POA-LMP23 (service parts no 610 285 2912) lamps. Since they contain mercury they can’t be placed into regular garbage.

How to reset the Sanyo PLC-SW15 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in monitor not tracking the lamp life properly.

NOTE: RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

Turn the Sanyo PLC-SW15 projector on.
Press the MENU button to access the ON-SCREEN MENU.
Press the POINT LEFT/RIGHT button to select the SETTING menu.
Press the SELECT button to open the SETTING MENU option.
Press the POINT DOWN button so the red-arrow appears.
Move down to the LAMP AGE option. Press SELECT to open the next option.
The message “Lamp replace monitor Reset?” will be displayed.
Click on the option YES to reset the timer.

Extend the life of the Sanyo POA-LMP31 lamp

Extend the life of your newly installed Sanyo POA-LMP23 (service parts no 610 285 2912) by following these tips:

Wait at least five minutes before turning the Sanyo PLC-SW15 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP23 (service parts no 610 285 2912) and prevent the Sanyo PLC-SW15 from overheating.

Tagged with: authentic lamps, genuine lamps, Lamp replacement, philips, projector, Projector LAMP, replacement lamps, Sanyo PLC-SW15, Sanyo POA-LMP23, Sanyo POA-LMP23 (service parts no 610 285 2912), Sanyo POA-LMP31

How to replace the Sanyo PLC-SW10 projector lamp

Shelagh McNallyPosted on March 20, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-SW10 Projector

When you notice a yellow blinking light on the top of your Sanyo PLC-SW10 projector, it’s time to replace the Sanyo POA-LMP23 (service parts no 610 285 2912).

BEFORE INSTALLATION

Be sure to purchase only genuine POALMP23 to protect your investment. While knock-off lamps can appear to be a bargain due to their cheaper prices, these counterfeit models can actually end up costing you more in the long run. Knock-offare manufactured with inferior parts that can damage the sensitive mechanisms in your Sanyo PLC-SW10 projector.

Buying a genuine Sanyo POA-LMP23 (service parts no 610 285 29123) gives you a lamp made to meet the specifications of your SANYO PLC-SW10 projector while keeping your warranty intact.

Looking for a less expensive option? Want more information? Watch our step-by-step video on replacing only the POA-LMP23 (service parts no 610 285 29123) bulb instead of the entire lamp housing.

STEP-BY-STEP INSTRUCTIONS FOR LAMP REPLACEMENT

1. Turn off the Sanyo PLC-SW10 projector and unplug the AC cord. Allow the projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

2. Underneath the Sanyo PLC-SW10 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the project.Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

3 Loosen both screws holding the Sanyo POA-LMP23 (service parts no 610 285 29123) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program..

4. Take the new Sanyo POA-LMP23 (610 285 29123) lamp cage by the handle—avoid touching the actual bulb a this can break or damage the lamp. Without forcing the lamp, place it into the slot.

5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP23 (61028529123) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SW10 projector will not turn on.

6. Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SW10 projector. If the Sanyo POA-LMP23 (service parts no 610 285 29123) lamp does not turn on after the warm-up period, try re-installing the lamp.

Reset the Lamp Replacement Monitor Timer by following the instructions below.

NOTE: BE sure to properly recycle your used Sanyo POA-LMP23 (service parts no 610 285 29123) lamps. Since they contain mercury they can’t be placed into regular garbage.

How to reset the Sanyo PLC-SW10 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your Sanyo POA-LMP23 (service parts no 610 285 29123) you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

Turn the Sanyo PLC-SW10 projector on.
Press the MENU button to access the ON-SCREEN MENU.
Press the POINT LEFT/RIGHT button to select the SETTING menu.
Press the SELECT button to open the SETTING MENU option.
Press the POINT DOWN button so the red-arrow appears.
Move down to the LAMP AGE option. Press SELECT to open the next option.
The message “Lamp replace monitor Reset?” will be displayed.
Click on the option YES to reset the timer.
RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

Extending the life of the Sanyo POA-LMP23 lamp

Extend the life of your newly installed Sanyo POA-LMP23 (service parts no 610 285 29123) by following these tips:

Wait at least five minutes before turning the Sanyo PLC-SW10 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sa nyo POA-LMP23 (service parts no 610 285 29123) and prevent the Sanyo PLC-SW10 from overheating.

Tagged with: authentic lamps, genuine lamps, philips, Projector LAMP, Sanyo PLC-SW10, Sanyo POA-LMP23, Sanyo POA-LMP23 (service parts no 610 285 29123), Sanyo POA-LMP31

When to replace your Sanyo POA-LMP 21

Shelagh McNallyPosted on March 16, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo POA-LMP 21, Sanyo POA-LMP21 (service parts no 610 290 6939)

The life of the Sanyo POA-LMP21j (service parts no 610 290 6939) lamp runs anywhere from 1,000 to 3,000 hours. It’s life cycle will vary depending on how often depending your projector is use and whether there is regular maintenance of the filters.

The life expectancy of your Sanyo POA-LMP21j (service parts no 610 290 6939)lamp depends on the amount of usage and whether the air filters are cleaned on a regular basis. A build up of dust on the filters will reduce the cooling fans effectiveness and may cause the lamp to overheat. It’s always a good idea to keep a spare lamp on hand so you can replace the lamp immediately and not wait to use the projector.

Only genuine Sanyo POA-LMP21j (service parts no 610 290 6939) lamps should be used when replacing the projector lamp order to keep your projector is good working order. The authentic POA-LMP21j has been manufactured to meet the specifications of the Sanyo projectors.

While knock-off lamps may seem like a bargain due to their low prices, these counterfeit lamps can damage the sensitive and expensive mechanisms and expensive mechanisms in your Sanyo projector and may also void your guarantee from the manufacturer. Purchasing a genuine Sanyo POA-LMP21j (610 290 6939) will ensure you keep your projector in good working order.

The Sanyo POA-LMP 21 can be used in the following projectors:

Sanyo PLC-SU20
Sanyo PLC-SU22
Sanyo PLC-XU20
Sanyo PLC-XU22

For step-by-step instructions on how to replace the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp, please click on your specific model listed below:

Sanyo PLC SU20N Projectior

Click here for step-by-step instructions on how to change the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp for the Sanyo PLC-SU20 projector.

Sanyo PLC SU22 Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp for the Sanyo PLC-SU22 projector.

Sanyo PLC-XU20

Click here for step-by-step instructions on how to change the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp for the Sanyo PLC-XU20 projector.

Sanyo PLC XU22-N projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp for the Sanyo PLC-XU22 projector.

Tagged with: authentic lamps, genuine lamps, Lamp replacement, Projector LAMP, replacement lamps, Sanyo PLC-SU20, Sanyo PLC-SU22, Sanyo PLC-XU20, Sanyo PLC-XU22, Sanyo POA-LMP21, Sanyo POA-LMP21 (service parts no 610 290 6939)

6 Steps to replacing the Sanyo PLC-XU22 projector lamp

Shelagh McNallyPosted on March 13, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC XU22-N projector

When your Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp is nearing its end of life you’ll see the Lamp Replace Indicator on the Sanyo PLC-XU22 projector flash red. You will need to replace the lamp immediately. Follow our step-by-step instructions to install the new Sanyo POA-LMP21j (610 290 6939) projector lamp.

Before installation

Buy your Sanyo POA-LMP21j (service parts no 610 290 6939) from an authorized manufacturer and avoid the lower-prices knock-off lamps. These counterfeit lamps are usually made with counterfeit parts that can damage sensitive mechanisms in your Sanyo PLC-XU22. This can end up costing you more money in the long run. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee.

Instructions for replacing the Sanyo PLC-XU22 Projector Lamp

1. Before installing the new Sanyo POA-LMP21j (service parts no 610 290 6939) lamp turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XU22 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

2. The lamp cover for the Sanyo PLC-XU22 is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.

3. Loosen both screws holding the Sanyo POA-LMP21j (6102906939) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP21j (service parts no 610 290 6939) lamp cage by the handle—avoid touching the actual bulb a this can break or damage the lamp. Without forcing the lamp, place it into the slot.

5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP21j (610 290 6939) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU22 projector will not turn on.

6. Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU22 projector. If the Sanyo POA-LMP21j (610 290 6939) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Counter Screen by following the instructions below.

NOTE: Be sure to properly recycle your used Sanyo POA-LMP21j (service parts no 610 290 6939) lamps. Since they contain mercury they can’t be placed into regular garbage.

How to reset the Sanyo PLC-XU22 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your Sanyo POA-LMP21j (service parts no 610 290 6939) you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

Turn the Sanyo PLC-XU22 projector on.
Press the MENU button to access the ON-SCREEN MENU.
Press the POINT LEFT/RIGHT button to select the SETTING menu.
Press the SELECT button to open the SETTING MENU option.
Press the POINT DOWN button so the red-arrow appears.
Move down to the LAMP AGE option. Press SELECT to open the next option.
The message “Lamp replace monitor Reset?” will be displayed.
Click on the option YES to reset the timer.
RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

Extend the life of the SANYO POA-LMP 21 lamp

Extend the life of your newly installed Sanyo POA-LMP21j (service parts no 610 290 6939) by following these tips:

Wait at least five minutes before turning the Sanyo PLC-XU22 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP21j (service parts no 610 290 6939) and prevent the Sanyo PLC-XU22 from overheating.

Tagged with: authentic lamps, genuine lamps, Lamp replacement, Projector LAMP, replacement lamps, Sanyo PLC-XU22 projector, Sanyo POA-LMP21, Sanyo POA-LMP21 (service parts no 610 290 6939), Sanyo POA-LMP33

How to replace the Sanyo PLC-XU20 projector lamp

Shelagh McNallyPosted on March 11, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XU20 Projector

Watch for the yellow blinking light on your Sanyo PLC-XU20’s Lamp Replacement Indicator. The blinking light indicates your Sanyo POA-LMP21 (service parts no 610 290 6939) lamp is reaching its end of life. Follow our easy step-by-step instructions to replace your projector lamp

Instructions for replacing the Sanyo PLC-XU20 Projector Lamp

It’s important to buy only a genuine POA-LMP21 to replace the old lamp. The price of generic knock-off lamps may be tempting but can cost you more money in the long run. Counterfeit lamps are not manufactured according to Sanyo’s specifications and can damage the sensitive (and expensive) mechanisms in your Sanyo PLC-XU20 projector.

Before installation

Before installing the new Sanyo POA-LMP21 (610 290 6939) lamp be sure to turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XU20 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Step-by-step instructions for replacing the Sanyo POA-LMP 21 Lamp Assembly

The lamp cover for the Sanyo PLC-XU20 is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
Loosen both screws holding the Sanyo POA-LMP21 (service parts no 610 290 6939) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side.
Be sure to dispose of the lamp properly through a local recycling program.
Take the new Sanyo POA-LMP21 (610 290 6939) lamp cage by the handle—avoid touching the actual bulb a this can break or damage the lamp. Without forcing the lamp, place it into the slot.
Once the lamp is in, tighten both screws on the Sanyo POA-LMP21 (6102906939) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU20 projector will not turn on.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU20 projector If the Sanyo POA-LMP21 (service parts no 610 290 6939) lamp does not turn on after the warm-up period, try re-installing the lamp.
Reset the Lamp Counter Screen by following the instructions below.

NOTE: BE sure to properly recycle your used Sanyo POA-LMP21 (610 290 6939) lamps. Since they contain mercury they can’t be placed into regular garbage.

How to reset the Sanyo PLC-XU20 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your Sanyo POA-LMP21 (service parts no 610 290 6939) you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

Turn the Sanyo PLC-XU20 projector on.
Press the MENU button to access the ON-SCREEN MENU.
Press the POINT LEFT/RIGHT button to select the SETTING menu.
Press the SELECT button to open the SETTING MENU option.
Press the POINT DOWN button so the red-arrow appears.
Move down to the LAMP AGE option. Press SELECT to open the next option.
The message “Lamp replace monitor Reset?” will be displayed.
Click on the option YES to reset the timer.
RESET the Lamp Replacement Monitor Timer ONLY WHEN the Sanyo POA-LMP21 (610 290 6939) lamp has been REPLACED.

Extend the life of the SANYO POA-LMP 21 lamp

Extend the life of your newly installed Sanyo POA-LMP21 (service parts no 610 290 6939) by following these tips:

Wait at least five minutes before turning the Sanyo PLC-XU20 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP21 (service parts no 610 290 6939) and prevent the Sanyo PLC-XU20 from overheating.

Tagged with: authentic lamps, genuine lamps, Lamp replacement, lamps, POA-LMP21, POA-LMP33, replacement lamps, Sanyo PLC-XU20, Sanyo POA-LMP21 (service parts no 610 290 6939)

Change your Sanyo PLC-SU22 projector lamp in 6 easy steps

Shelagh McNallyPosted on March 11, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC SU22 Projector

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-SU22 LAMP REPLACEMENT

When it’s time to change your lamp on your Sanyo PLC-SU22 projector, you’ll notice the yellow light blinking on the Lamp Indicator found on the top control panel.

You’ll need a Sanyo POA-LMP21 (service parts no 610 290 6939) lamp as a replacement.

BEFORE INSTALLATION

Be sure to buy an authentic Sanyo POA-LMP21 (service parts no 610 290 6939) lamp bought from a verified source. These genuine lamps have manufactured to meet the specifications of the PLC-XE40/PLC-XE45 projector. Resist the temptation to buy a cheaper POALMP21 as these generic lamps often use counterfeit parts that can damage the sensitive mechanisms in your Sanyo PLC-SU22 projector.

REPLACING THE SANYO POA-LMP 21 LAMP

The lamp cover for the Sanyo PLC-SU22 is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
Loosen both screws holding the Sanyo POA-LMP21 (610 290 6939) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.
Take the new Sanyo POA-LMP21 (6102906939) lamp cage by the handle—avoid touching the actual bulb as this can break or damage the lamp. Without forcing the lamp, place it into the slot.
Once the lamp is in, tighten both screws on the Sanyo POA-LMP21 (service parts no 610 290 6939) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SU22 projector will not turn on.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SU22 projector. If the Sanyo POA-LMP21 (610 290 6939) lamp does not turn on after the warm-up period, try re-installing the lamp.
Reset the Lamp Counter Screen by following the instructions below.

NOTE: BE sure to properly recycle your used Sanyo POA-LMP21 (service parts no 610 290 6939) lamps. Since they contain mercury they can’t be placed into regular garbage.

RESETTING THE LAMP REPLACEMENT MONITOR TIMER

Turn the projector on.
Press the MENU button to access the ON-SCREEN MENU.
Press the POINT LEFT/RIGHT button to select the SETTING menu.
Press the SELECT button to open the SETTING MENU option.
Press the POINT DOWN button so the red-arrow appears.
Move down to the LAMP AGE option. Press SELECT to open the next option.
The message “Lamp replace monitor Reset?” will be displayed.
Click on the option YES to reset the timer.
RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

MAKE THE SANYO POA-LMP 21 LAMP LAST LONGER

Extend the life of your newly installed Sanyo POA-LMP21 (service parts no 610 290 6939) by following these tips:

Wait at least five minutes before turning the Sanyo PLC-SU22 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP21 (service parts no 610 290 6939) and prevent the Sanyo PLC-SU22 from overheating.

Tagged with: authentic lamps, authentic projector lamps, genuine lamps, genuine projector lamps, lamp enclosure, Lamp replacement, POA-LMP21, POA-LMP33, replacement lamps, Sanyo PLC-SU22, Sanyo POA-LMP21 (service parts no 610 290 6939)

Step-by-step instructions for Sanyo PLC-SU20 lamp replacement

Shelagh McNallyPosted on March 11, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC SU20N Projectior

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-SU20 LAMP REPLACEMENT

The life span for the projector lamp in a Sanyo PLC-SU20 projector depends on how much the projector is used and how often the air filter is cleaned. With proper care and maintenance, you can expect between two to three thousand hours of use.

When you are approaching end of life with your lamp, the Lamp Replacement Indicator will blink yellow. When this happens replace the lamp with a genuine Sanyo POA-LMP21 (service parts no 610 290 6939).

Be sure to purchase an authentic lamp to ensure you are getting a Sanyo POA-LMP21 (610 290 6939) that has been made to fit properly into the Sanyo PLC-SU20 projector. Installing a generic lamp can damage your projector and may cost you more in the long run.

Before Installing

Allow the Sanyo PLC-SU20 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP21 (service parts no 610 290 6939) lamp.

Replacing the Sanyo POA-LMP 21 Lamp Assembly

The lamp cover for the Sanyo PLC-SU20 is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
Loosen both screws holding the Sanyo POA-LMP21 (service parts no 610 290 6939) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side.
Be sure to dispose of the lamp properly through a local recycling program.
Take the new Sanyo POA-LMP21 (service parts no 610 290 6939) lamp cage by the handle—avoid touching the actual bulb as this can break or damage the lamp. Without forcing the lamp, place it into the slot.
Once the lamp is in, tighten both screws on the Sanyo POA-LMP21 (610 290 6939) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SU20 projector will not turn on.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SU20 projector If the Sanyo POA-LMP21 (6102906939) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Replacement Monitor by following the instructions below.

NOTE: BE sure to properly recycle your used Sanyo POA-LMP21 (service parts no 610 290 6939) lamps. Since they contain mercury they can’t be placed into regular garbage.

RESETTING THE LAMP REPLACEMENT MONITOR TIMER FOR SANYO PLC-SU20 PROJECTOR

Turn the Sanyo PLC-SU20 projector on.
Press the MENU button to access the ON-SCREEN MENU.
Press the POINT LEFT/RIGHT button to select the SETTING menu.
Press the SELECT button to open the SETTING MENU option.
Press the POINT DOWN button so the red-arrow appears.
Move down to the LAMP AGE option. Press SELECT to open the next option.
The message “Lamp replace monitor Reset?” will be displayed.
Click on the option YES to reset the timer.
RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

MAKING SANYO POA-LMP21 LAMP LAST LONGER

Extend the life of your newly installed Sanyo POA-LMP21 (service parts no 610 290 6939) by following these tips:

Wait at least five minutes before turning the Sanyo PLC-SU20 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP21 (service parts no 610 290 6939) and prevent the Sanyo PLC-SU20 from overheating.

Tagged with: authentic lamps, authentic projector lamps, genuine lamps, installation, Lamp replacement, POA-LMP21, replacement lamps, replacement projector lamps, Sanyo PLC-SU20, Sanyo POA-LMP21 (service parts no 610 290 6939)

When to replace Sanyo POA-LMP18

Shelagh McNallyPosted on March 1, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Find which projectors are compatible with the Sanyo POA-LMP18.

The life of the Sanyo POA-LMP18 (service parts no 610 279 5417) lamp runs anywhere from 1,000 to 3,000 hours. It’s life cycle will vary depending on how often depending your projector is use and whether there is regular maintenance of the filters.

The life expectancy of your Sanyo POA-LMP18 (service parts no 610 279 5417) lamp depends on the amount of usage and whether the air filters are cleaned on a regular basis. A build up of dust on the filters will reduce the cooling fans effectiveness and may cause the lamp to overheat. It’s always a good idea to keep a spare lamp on hand so you can replace the lamp immediately and not wait to use the projector.

Only genuine Sanyo POA-LMP18 (service parts no 610 279 5417) lamps should be used when replacing the projector lamp order to keep your projector is good working order. The authentic POA-LMP18 has been manufactured to meet the specifications of the Sanyo projectors.

While knock-off lamps may seem like a bargain due to their low prices, these counterfeit lamps can damage the sensitive and expensive mechanisms and expensive mechanisms in your Sanyo projector and may also void your guarantee from the manufacturer. Purchasing a genuine Sanyo POA-LMP18 will ensure you keep your projector in good working order.

The Sanyo POA-LMP18 can be used in the following projectors:

For step-by-step instructions on how to replace the Sanyo POA-LMP18 (service parts no 610 279 5417) projector lamp, please click on your specific model listed below:

Sanyo PLC-SP20N Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP18 (service parts no 610 279 5417) projector lamp for the Sanyo PLC-SP20N projector.

Sanyo PLC-XP07B Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP18 (service parts no 610 279 5417) projector lamp for the Sanyo PLC-XP07B projector.

Looking for a less expensive option? Want more information? Watch our step-by-step video on replacing only the Sanyo POA-LMP18 (service parts no 610 279 5417) bulb instead of the entire lamp housing.

Tagged with: authentic lamps, genuine lamps, lamp enclosure, Lamp replacement, POA-LMP18, Sanyo PLC-SP20N, Sanyo PLC-XP07B, Sanyo PLC-XP10, Sanyo POA-LMP18, Sanyo POA-LMP18 (service parts no 610 279 5417)

How to replace the Sanyo PLC-XP10 projector lamp

Shelagh McNallyPosted on March 1, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XP10 Projector

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XP10 LAMP REPLACEMENT

If your projector Sanyo PLC-XP10 lamp no longer turns on, it needs to be replaced. If the picture is dim or looks unnatural the Sanyo POA-LMP17 (service parts no 610 276 3010) is reaching its end of life. If the Replace Lamp Indicator light on the front panel is blinking orange, you must replace the S Sanyo POA-LMP17 (610 276 3010) immediately. Follow our simple step-by-step instructions to replace your lamp in the Sanyo PLC-XP10 projector easily.

The lifespan of your Sanyo POA-LMP17 lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

Before Installation

Buy your Sanyo POA-LMP17 (610 276 3010) from an authorized manufacturer and avoid the lower-priced knock-off lamps. These counterfeit lamps are usually made with inferior parts that can damage your projector, they may end up costing you more if the damage the sensitive mechanisms in your Sanyo PLC-XP10 projector. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee.

Looking for a less expensive option? Want more information? Watch our step-by-step video on replacing only the Sanyo POA-LMP17 (service parts no 610 276 3010) bulb instead of the entire lamp housing.

Replacing the Sanyo POA-LMP17 Lamp Assembly

Allow the Sanyo PLC-XP10 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP17 lamp.
The lamp cover for the PLC-XP10 projector is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
Inside you’ll find the Sanyo POA-LMP17 (service parts no 610 276 3010) lamp cage. Loosen both screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.
Taking the new Sanyo POA-LMP17 (service parts no 610 276 3010) lamp cage by the handle—avoid touching the actual bulb as this can break or damage the lamp. Without forcing the lamp, place it into the slot.
Once the lamp is in, tighten both screws on the Sanyo POA-LMP17 Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XP10 projector will not turn on.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XP10 projector If the Sanyo POA-LMP17 (610 276 3010) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Counter Screen by following the instructions below.

NOTE: Your old Sanyo POA-LMP17 (service parts no 610 276 3010) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE LAMP REPLACEMENT MONITOR TIMER FOR SANYO PLC-XP10

In order for the projector to properly track the lamp life of your Sanyo POA-LMP17 (service parts no 610 276 3010) you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

Press SELECT (rear click) to have the SETTING DISPLAY screen appear.
Press the POINT DOWN button and a red arrow shows up on screen.
Using the POINT UP/DOWN button, select the LAMP PAGE and then press SELECT.
You’ll see the message “Lamp replace monitor reset?“
Move the arrow to YES and press SELECT.
OK is shown for confirmation. Press YES and then the SELECT button.
Move the arrow QUIT and press SELECT to exit the MENU and return to the screen.
Your newly installed Sanyo POA-LMP17 (610 276 3010) should last between 1,000 to 2,000 hours depending on usage and maintenance of the Sanyo PLC-XP10 projector.

TIPS FOR EXTENDING THE SANYO POA-LMP17 LAMP

Make your newly installed Sanyo POA-LMP17 (service parts no 610 276 3010) last longer:

Wait at least five minutes before turning the Sanyo PLC-XP10 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP17 (service parts no 610 276 3010) and prevent the Sanyo PLC-XP10 from overheating.

Tagged with: authentic lamps, genuine lamps, lamp enclosure, Lamp replacement, POA-LMP18, projector, Projector LAMP, Sanyo PLC-XP10 projector, Sanyo POA-LMP18, Sanyo POA-LMP18 (service parts no 610 279 5417)