We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 138

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
Sanyo PLC-XW55 projector, Sanyo POA-LMP107 (service parts no 610 330 4564)

Sanyo PLC-XW55 projector

When it’s time to change your projector lamp on either your SanyoPLC-XW50 or Sanyo PLC-XW55 projector, you’ll notice a yellow light blinking on the Top Control panel. This is the lamp replacement indicator letting you know it’s to replace your Sanyo POA-LMP107 (service parts no 610 330 4564) projector lamp.

It’s important the buy only a genuine POA-LMP107 to replace the old lamp. The price of counterfeit knock-off lamps may be tempting but can cost you more money in the long run. Counterfeit lamps are not manufactured according to Sanyo’s specifications and can damage the sensitive (and expensive) mechanisms in your Sanyo PLC-XW50/PLC-XW55.

Sanyo PLC- XW50 projector, Sanyo POA-LMP107 (service parts no 610 330 4564)

Sanyo PLC- XW50 projector

STEP-BY-STEP INSTRUCTIONS FOR LAMP REPLACEMENT

Before installation of the Sanyo POA-LMP107 (service parts no 610 330 4564) lamp: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XW50/PLC-XW55 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the Sanyo POA-LMP107 (610 330 4564) lamp

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

Sanyo PLC-XE32 Lamp Cover, Sanyo POA-LMP107 (service parts no 610 330 4564)1. Underneath the Sanyo PLC-XW50/PLC-XW55 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the projector. Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the two screws on either side of each the Sanyo POA-LMP107 (service parts no 610 330 4564) lamp. Grab the handle on the lamp cage and gently pull out the lamp. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

3. Take the new Sanyo POA-LMP107 (610-330-4564) lamp cage by the handle and gently maneuver it into place.

Sanyo PLC-XE32 Lamp Assembly, Sanyo POA-LMP107 (service parts no 610 330 4564)

4. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten screws.

6. Re-connect the power cord and turn on the Sanyo PLC-XW50/PLC-XW55 projector.

Resetting the Lamp Replacement counter on the Sanyo PLC-XW50/PLC-XW55

Reset the Lamp Replacement Counter only when the Sanyo POA-LMP107 (service parts no 610 330 4564) lamps has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions,  fire hazard and other accidents.

Sanyo PLC-XW50/PLC-XW55 lamp reset option, Sanyo POA-LMP107 (service parts no 610 330 4564)

  • Turn the Sanyo PLC-XW50/PLC-XW55 projector on.
  • Press the Menu option to display the On-Screen Menu.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Another confirmation dialog box appears, select YES.Sanyo PLC-XW50/PLC-XW55, Sanyo POA-LMP107 (service parts no 610 330 4564)
  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Clean your filter before before using the Sanyo PLC-XW50/PLC-XW55 projector to ensure a longer life for your newly installed projector lamp.

Cleaning the air your filter in the Sanyo PLC-XW50/PLC-XW55 will ensure a longer life for your newly installed Sanyo POA-LMP107 (service parts no 610 330 4564) projector lamp.

 

Tagged with: , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
Sanyo PLC-XE32 projector, Sanyo POA-LMP107 (service parts no 610 330 4564)

Sanyo PLC-XE32 projector

When it’s time to change your projector lamp on your Sanyo PLC-XE32 projector, the lamp replacement indicator turns yellow and starts blinking. When this happens, it’s time to replace your Sanyo POA-LMP107 (service parts no 610 330 4564) lamp.

Be sure to purchase only a genuine POA-LMP107 to protect your projector from being damaged by counterfeit lamps. Beware of cheaper versions that can damage the sensitive mechanisms in your Sanyo PLC-XE32 projector.

STEP-BY-STEP INSTRUCTIONS FOR LAMP REPLACEMENT

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XE32 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the Sanyo POA-LMP107 (610-330-4564) lamp

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

Sanyo PLC-XE32 Lamp Cover,Sanyo POA-LMP107 (service parts no 610 330 4564) 1. Underneath the Sanyo PLC-XE32 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the projector. Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the two screws on either side of each the  Sanyo POA-LMP107 (service parts no 610 330 4564) lamp. Grab the handle on the lamp cage and gently pull out the lamp. Place to one side.

3. Take the new Sanyo POA-LMP107 (6103304564) lamp cage by the handle and gently maneuver it into place.

Sanyo PLC-XE32 Lamp Assembly Unit, Sanyo POA-LMP107 (service parts no 610 330 4564)

POA-LMP107

4. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten screws.

6. Re-connect the power cord and turn on the Sanyo PLC-XE32 projector.

Resetting the Lamp Replacement counter on the Sanyo PLC-XE32 Projector

Reset the Lamp Replacement Counter only when the Sanyo POA-LMP107 (service parts no 610 330 4564) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions,  fire hazard and other accidents.

Sanyo PLC-XE32 lamp reset, Sanyo POA-LMP107 (service parts no 610 330 4564)

  • Turn the Sanyo PLC-XE32 projector on.
  • Press the Menu option to display the On-Screen Menu.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Another confirmation dialog box appears, select YES.Sanyo PLC-XE32 lamp reset, Sanyo POA-LMP107 (service parts no 610 330 4564)
  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Cleaning the air your filter in the Sanyo PLC-XW32 will ensure a longer life for your newly installed Sanyo POA-LMP107 (service parts no 610 330 4564) projector lamp.

Tagged with: , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
Sanyo PLC-SU73 projector, Sanyo POA-LMP106 service parts no 610 332 3855

Sanyo PLC-SU73 projector

When it’s time to change your  lamp on your Sanyo PLC-SU70/PLC-XU73 projector, the lamp indicator will turn yellow and start blinking. Be sure to choose an authentic Sanyo POA-LMP106 (service part no 610 332 3855) projector lamp.

Buying only genuine POALMP106s lamps protects your investment by ensuring you are installing a projector lamp that is guaranteed. The cheaper versions are often counterfeit models that can damage the sensitive mechanisms in your Sanyo projector.

For additional savings and an enviro-friendly option, you can just replace the Sanyo POA-LMP106 bulb and re-use the lamp cage. Learn how in our video guide: Sanyo POA-LMP106 replacement lamp housing guide.

Sanyo PLC-SU70 projector, Sanyo POA-LMP106 service parts no 610 332 3855

Sanyo PLC-XU70 projector

STEP-BY-STEP INSTRUCTIONS FOR LAMP REPLACEMENT

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-SU70/PLC-XU73 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the Sanyo POA-LMP106 (610 332 3855) lamp

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

Sanyo PLC-SU70/PLC-XU73 lamp cover, Sanyo PLC-SU70 projector, Sanyo POA-LMP106 service parts no 610 332 3855 1. Underneath the Sanyo PLC-SU70/PLC-XU73 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the project.Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the two screws on either side of each the Sanyo POA-LMP106 (service parts no 610 332 3855) lamp. Grab the handle on the lamp cage and gently pull out the lamp. Place to one side. BE sure to properly recycle your used Sanyo POA-LMP106 (610-332-3855) lamps. Since they contain mercury they can’t be placed into regular garbage.

Sanyo PLC-SU70/PLC-XU73 projector, Sanyo POA-LMP106 service parts no 610 332 38553. Take the newSanyo POA-LMP106 (service part no 610 332 3855) lamp cage by the handle and gently maneuver it into place.

4. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten screws.

6. Re-connect the power cord and turn on the Sanyo PLC-SU70/PLC-XU737 projector.

Resetting the Lamp Replacement counter on the Sanyo PLC-SU70/PLC-XU73 Projector

Reset the Lamp Replacement Counter only when the Sanyo POA-LMP106 (6103323855) has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

  • Sanyo PLC-SU70/PLC-XU73 lamp counter reset, Sanyo POA-LMP106 service parts no 610 332 3855Turn the Sanyo Sanyo PLC-SU70/PLC-XU73 projector on.
  • Press the Menu option to display the On-Screen Menu.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Another confirmation dialog box appears, select YES.

Sanyo PLC-SU70/PLC-XU73 lamp reset optioSanyo PLC-SU70/PLC-XU73 lamp counter reset, Sanyo POA-LMP106 service parts no 610 332 3855

  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.

 

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Prolong the life of your newly installed Sanyo POA-LMP106 (service parts no 610 332 3855) by regularly cleaning of the air filter on the Sanyo PLC-XE45 projector.

 

 Replace_Bulb_Keep_Cage

For additional savings and an enviro-friendly option, you can just replace the Sanyo POA-LMP106 bulb and re-use the lamp cage. Learn how in our video guide: Sanyo POA-LMP106 replacement lamp housing guide.

Tagged with: , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo POA-LMP106 (service parts no 610 332 3855)/Wondering when to change the Sanyo POA-LMP106 (service parts no 610 332 3855)?

Your Sanyo POA-LMP106 (service parts no 610 332 3855) projector lamp has between 2,000 to 3,000 hours before it needs to be replaced. This may be less if your filters are not cleaned on a regular basis.

Replace_Bulb_Keep_CageFor additional savings and an enviro-friendly option, you can just replace the Sanyo POA-LMP106 bulb and re-use the lamp cage. Learn how in our video guide: Sanyo POA-LMP106 replacement lamp housing guide.

Projectors using POA-LMP106

XE45
PLC-SU70/PLC-XU73
PLC-XU74
PLC-XU84/PLC-XU87

Be sure to use the correct brand projector lamp bought from a verified source that has been manufactured to meet the specifications of your projector. Resist the temptation to buy a cheaper counterfeit model as this can damage the sensitive mechanisms in your Sanyo projectors.

See below for the step-by-step instructions on replacing the Sanyo POA-LMP106 (service part no 610 332 3855) lamps for Sanyo projectors listed above.

Sanyo Lamp Replace Indicator

PLC-SU70/PLC-XU73/PLC or PLC-XE40/PLC-XE45 or PLC-XU74 or PLC-XU83/PLC-XU86 or PLC-XU84/PLC-XU87 Lamp replacement indicator

As the lamp reaches its end of life, the Lamp Replace indicator lights turns yellow and starts to blink.

When the lamp life is used up and at 0 hour, the Lamp replacement icon will appear on screen, indicating that is it’s urgent to replace the Sanyo POA-LMP106 (service parts no 610 332 3855) lamp.

PLC-SU70/PLC-XU73/PLC or PLC-XE40/PLC-XE45 or PLC-XU74 or PLC-XU83/PLC-XU86 or PLC-XU84/PLC-XU87 lamp repalcement icon

You must wait for 90 seconds after changing Lamp Mode before you can access this option again.

Click on your Sanyo Projector for step-by-step instructions on replacing your Sanyo POA-LMP106 (service parts no 610 332 3855) lamp:

 

Sanyo PLC-XE45 projector, Sanyo POA-LMP106 610 332 3855

 

Sanyo projectors PLC-XE45

Click here for step-by-step instructions on how to change the Sanyo POA-LMP106 (service parts no 610 332 3855) projector lamp for the Sanyo XE45 projector.

 

 

Sanyo projector PLC-XU74, Sanyo POA-LMP106 (service parts no 610 332 3855)/ Sanyo POA-LMP90 (service part no 610 323 0726)

Sanyo projectors PLC-XU73/PLC-SU70

Click here for step-by-step instructions on how to change the Sanyo POA-LMP106 (service parts no 610 332 3855) projector lamp for the PLC-SU70/PLC-XU73 projector.

 

Sanyo projector PLC-XU74, Sanyo POA-LMP106 (service parts no 610 332 3855)/ Sanyo POA-LMP90 (service part no 610 323 0726)

Sanyo projector PLC-XU74

 

 

 

Sanyo projectors PLC-XU84/PLC-XU87, Sanyo POA-LMP106 (service parts no 610 332 3855)/ Sanyo POA-LMP90 (service part no 610 323 0726)

Sanyo projector PLC-XU84/PLC-XU87

Tagged with: , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
Sanyo PLC-XU74 projector, Sanyo POA-LMP106 (service part no 610 332 3855)

Sanyo PLC-XU74 projector

Wondering when to replacement your projector lamp on your Sanyo PLC-XU74 projector? When it’s time to change your projector lamp indicator will blink yellow to indicate the end of life for your Sanyo POA-LMP106 (service part no 610 332 3855) lamp.

Protect your investment and buy an authentic projector lamp. Buy only genuine POALMP106 and avoid cheaper versions as these are often counterfeit models with less durable parts that can damage the sensitive mechanisms in your Sanyo PLC-XU74 projector.

STEP-BY-STEP INSTRUCTIONS FOR LAMP REPLACEMENT

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XU74 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the Sanyo POA-LMP106 (6103323855) lamp

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

Sanyo PLC-XU74 lamp cover, Sanyo POA-LMP106 (service part no 610 332 3855)1. Underneath the Sanyo PLC-XU74 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the project.Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the two screws on either side of each the POA-LMP106 (610-332-3855) lamp. Grab the handle on the lamp cage and gently the lamp. Place to one side.

Sanyo PLC-XU74 lamp assembly, Sanyo POA-LMP106 (service part no 610 332 3855)3. Take the new POA-LMP106 (service part no 610 332 3855) lamp cage by the handle and gently maneuver it into place.

4. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten screws.

6. Re-connect the power cord and turn on the Sanyo PLC-XU74 projector.

For additional savings and an enviro-friendly option, you can just replace the Sanyo POA-LMP106 bulb and re-use the lamp cage. Learn how in our video guide: Sanyo POA-LMP106 replacement lamp housing guide.

Resetting the Lamp Replacement counter on the Sanyo PLC-XU74 Projector

Reset the Lamp Replacement Counter only when the POA-LMP106 (service part no 610 332 3855) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Sanyo PLC-XU74 lamp reset, POA-LMP106 (service part no 610 332 3855)

  • Turn the Sanyo PLC-XU74 projector on.
  • Press the Menu option to display the On-Screen Menu.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Another confirmation dialog box appears, select YES.

Sanyo PLC-XU74 lamp reset, POA-LMP106 (service part no 610 332 3855)

  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.

 

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Clean your air filter on the Sanyo PLC-XU74 projector and the Sanyo POA-LMP106 (service part no 610 332 3855) will last longer.

 

 

 Replace_Bulb_Keep_Cage

For additional savings and an enviro-friendly option, you can just replace the Sanyo POA-LMP106 bulb and re-use the lamp cage. Learn how in our video guide: Sanyo POA-LMP106 replacement lamp housing guide.

Tagged with: , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
Sanyo PLC-XU86 projector, POA-LMP90 (service parts no 610 323 0726

Sanyo PLC-XU86 projector

This guide shows you how to change the Sanyo PLC-XU83/PLC-XU86 projector lamp.

When it’s time to change your projector lamp, the lamp indicator on your PLC-XU83/PLC-XU86 lamp will blink yellow. Be sure to use Sanyo POA-LMP90 (service parts no 610 323 0726) lamp for the replacement.

Protect your investment and buy an authentic projector lamp. Avoid the temptation to purchase a cheaper version of the POALMP90 as these are often counterfeit models with less durable parts that can damage the sensitive mechanisms in your Sanyo PLCXU83/PLCXU86 projector.

Sanyo_Video_Lamp_ReplacFor additional savings and an enviro-friendly option, you can just replace the Sanyo POA-LMP90 (service part no 610 323 0726) bulb and re-use the lamp cage. Learn how in our video guide: Sanyo POA-LMP90 replacement lamp housing guide.
Sanyo PLC-XU83 projector

Sanyo PLC-XU83 projector

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XU83/PLC-XU86 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

STEP-BY-STEP INSTRUCTIONS

Sanyo PLC-XU83/PLC-XU86 lamp cover, Sanyo POA-LMP90 (service parts no 610 323 0726)1. Underneath the Sanyo PLC-XU83/PLC-XU86 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the projector. Using a Philips screwdriver loosen the screw holding the projector lamp cover in place. Put the cover to one side.

2. Remove the two screws on either side of each the POA-LMP90 (service parts no 610 323 0726) projector lamp. Grab the handle on the  projector lamp cage and gently remove the lamp. Place to one side.

Sanyo PLC-XU83/PLC-XU86 lamp assembly, Sanyo POA-LMP90 (service parts no 610 323 0726)3. Take the new POA-LMP90 (6103230726) projector lamp by the handle and gently maneuver it into place.

4. Avoid touching the glass or the bulb. The projector lamp should slide in easily – don’t force it. Once the lamp is in, tighten the screws on the Projector Lamp Assembly.

5. Replace the Projector Lamp Hazard Cover and tighten screws.

6. Re-connect the power cord and turn on the Sanyo PLC-XU83/PLC-XU86 projector. You’re ready to reset the lamp counter.

Resetting the Lamp Replacement counter

Reset the Lamp Replacement Counter only when the Sanyo POA-LMP90 projector lamp has been replaced. Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Sanyo PLC-XU83/PLC-XU86 lamp replace counter, Sanyo POA-LMP90 (service parts no 610 323 0726)

  • Turn the Sanyo PLC-XU83/PLC-XU86 projector on.
  • Press the Menu option to display the On-Screen Menu.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Another confirmation dialog box appears, select YES.

Sanyo PLC-XU83/PLC-XU86 lamp replace counter, Sanyo POA-LMP90 (service parts no 610 323 0726)

  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Cleaning you air filter regularly will make the Sanyo POA-LMP90 projector lamp last longer.

 

Tagged with: , , , , ,

by avatarShelagh McNallyPosted on Posted in Projector Lamp Replacement Guides — No Comments ↓
Sanyo PLC-XU87, Sanyo POA-LMP106 service parts no 610 332 3855

Sanyo PLC-XU87 projector

Wondering when it’s time to change your projector lamp? Your PLC-XU84/PLC-XU87 lamp indicator will blink yellow and the lamp replacement icon will light up when its time to replace your Sanyo POA-LMP106 (service part no 610 332 3855) lamp.

Sanyo PLC-XU87/PLC-XU84 lamp icon, Sanyo POA-LMP106 service parts no 610 332 3855

Lamp icon

Protect your investment and buy an authentic projector lamp. Avoid the temptation to purchase a cheaper version of the POALMP106 as these are often counterfeit models with less durable parts that can damage the sensitive mechanisms in your PLC-XU84/PLC-XU87 projector.

Sanyo PLC-XU84 projector, Sanyo POA-LMP106 service parts no 610 332 3855

Sanyo projector PLC-XU84

STEP-BY-STEP INSTRUCTIONS FOR LAMP REPLACEMENT

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XU84/PLC-XU87 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the Sanyo POA-LMP106 lamp

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

Sanyo PLC-XU87/PLC-XU84 lamp cover, Sanyo POA-LMP106 service parts no 610 332 38551. Underneath the Sanyo PLC-XU84/PLC-XU87 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the project.Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the two screws on either side of each the Sanyo POA-LMP106 (service part no 610 332 3855) lamp. Grab the handle on the lamp cage and gently the lamp. Place to one side.

Sanyo PLC-XU87/PLC-XU84 lamp cover, Sanyo POA-LMP106 service parts no 610 332 38553. Take the new Sanyo POA-LMP106 (610-332-3855) lamp cage by the handle and gently maneuver it into place. Be sure to dispose of the lamp properly through a local recycling program.

4. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten screws.

6. Re-connect the power cord and turn on the Sanyo PLC-XU84/PLC-XU87 projector.

Resetting the Lamp Replacement counter on the Sanyo PLC-XU84/PLC-XU87 Projector

Reset the Lamp Replacement Counter only when the Sanyo POA-LMP106 (service part no 610 332 3855) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

POA-LMP106 Lamp Counter Option for Sanyo PLC-XU84/XU87 Projector

  • Turn the Sanyo PLC-XU84/PLC-XU87 projector on.
  • Press the Menu option to display the On-Screen Menu.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Another confirmation dialog box appears, select YES.

Sanyo PLC-XU84/PLC-XU87 lamp reset, Sanyo POA-LMP106 service parts no 610 332 3855

  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.

 

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Cleaning the air filter regularly will prolong the life of the Sanyo POA-LMP106 (service part no 610 332 3855) lamp.

 

 Replace_Bulb_Keep_Cage

For additional savings and an enviro-friendly option, you can just replace the Sanyo POA-LMP106 bulb and re-use the lamp cage. Learn how in our video guide: Sanyo POA-LMP106 replacement lamp housing guide.

 

 

Tagged with: , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XF30NL Projector, Sanyo POA-LMP39 service part no 610 292 4848Your Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 series projector lamps have between 2,000 to 3,000 hours before they need to be replaced. This may be less if your filters are not cleaned on a regular basis. When it’s time to change your PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 series lamp you’ll notice a flashing light on the either the Lamp Indicator.

Be sure to use the same type of projector lamp bought from a verified source that has been manufactured to meet the specifications. See below for the correct POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamp to use with your particular model and links for step-by-step instructions for replacing the lamps in all Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors.

Resist the temptation to buy a cheaper counterfeit model as this can damage the sensitive mechanisms in your Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors. Check your model to see if you’ll need two replacement lamps for your projector.

Lamp Indicator Sanyo PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, Sanyo PLC-XF30NL Projector, Sanyo POA-LMP39 service part no 610 292 4848Sanyo Lamp Replace Indicator

As the lamp reaches its end of life, the Lamp Replace indicator lights turns yellow indicating it’s time for a new POA-LLB02 / POA-LMP39 (610-292-4848) as the current lamp is nearing end of life. If the POA-LLB02 / POA-LMP39 (service part no 610 292 4848)9 light does  burn out, then the indicator light will be flashing. If your projector has more than one lamps, check the number of the lamp shown on screen as Lamp Status Display on the Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors so you can determine which lamp needs to be replaced.

On Screen Indicators

Lamp Indicator Sanyo PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, Sanyo PLC-XF30NL Projector, Sanyo POA-LMP39 service part no 610 292 4848

The Lamp Status Display appears on screen showing the status of each lamp. This will be the same menu for  all Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors.

 

Lamp Indicator Sanyo PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, Sanyo PLC-XF30NL Projector, Sanyo POA-LMP39 service part no 610 292 4848Yellow Lamp: Lamp lights normally and is ON

Dim Lamp: Projection Lamp is turned off.

 

Lamp Indicator Sanyo PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, Sanyo PLC-XF30NL Projector, Sanyo POA-LMP39 service part no 610 292 4848Red Lamp: Projections Lamp is nearing its end. When image becomes darker replace lamp. The LAMP REPLACE indicator will be flashing yellow.

 

Lamp Indicator Sanyo PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, Sanyo PLC-XF30NL Projector, Sanyo POA-LMP39 service part no 610 292 4848X mark on Lamp: Projection lamp is defective or fails to be turned on. Restart the projector and if the X still appears, replace the lamp marked with the X.

Sanyo Lamp Mode Changeover

When a lamp is no longer working, the Lamp Management Function (Lamp Mode) automatically changes the combination of lighting from either two lamps to one lamp being used.

The Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors series gives you the option of extending your lamp life by manually changing the Lamp Mode to use only one lamp. To do this:

  1. Press Menu button to get to the On-Screen Menu.
  2. Press Point left/right buttons to select Setting and press Select button. Setting dialog box appears.
  3. Press Point Down button to move a red frame pointer to Lamp Mode.
  4. Set the 2 Lamp Mode to 1 Lamp Mode lamp mode by pressing Point left/right buttons.
  5. When you switch the Lamp Mode from using 2 lamps to using 1 lamp the image becomes a little darker.
  6. When you switch the Lamp Modefrom using 1 lamp to using 2 lamps, the image becomes a little brighter gradually.

You must wait for 90 seconds after changing Lamp Mode before you can access this option again.

Click on your Sanyo Projector for step-by-step instructions on how to replace your lamp.

Lamp series: POA-LLB02/POA-LLB02 / POA-LMP39 (610 292 4848)

Sanyo PLC-EF30, Sanyo POA-LMP39 service part no 610 292 4848

Sanyo PLC-EF30

Click here for step-by-step instructions on how to change the  PLC-EF30 lamp.

 

Sanyo PLC-EF31/ PLC-EF31NL / PLC-EF31N/ PLC-EF32 Projector, Sanyo POA-LMP39 service part no 610 292 4848

Sanyo PLC-EF31/ PLC-EF31NL / PLC-EF31N/ PLC-EF32

Click here for step-by-step instructions on how to change the PLC-EF31/EF32 series lamp

 

Sanyo PLC-XF31 Projector, Sanyo POA-LMP39 service part no 610 292 4848

Sanyo PLC-XF31

Click here for step-by-step instructions on how to change the PLC XF31 series lamp.

 

Sanyo PLC-XF30/PLC-XF31 Projector, Sanyo POA-LMP39 service part no 610 292 4848

Sanyo PLC-XF30/ XF30NL

Click here for step-by-step instructions on how to change PLC-XF30 series lamp.

 

The green alternative

Replace_Bulb_Keep_CageIf you are looking an option that is more eco-friendly and can save you some money, consider replacing only the lamp and re-using the original lamp cage. Watch our step-by-step tutorial to show you what is needed.

Tagged with: , , , , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
Sanyo PLC-XF31 projector, Sanyo POA-LMP39 service part no 610 292 4848

Sanyo PLC-XF31 Projector

When it’s time to change your lamp on your  PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, you’ll notice the yellow light blinking on the lamp indicator.

 

 

 

 

Sanyo PLC-XF30NL projector, Sanyo POA-LMP39 service part no 610 292 4848

Sanyo PLC-XF30NL Projector

Be sure to use the same type of Sanyo projector lamp bought from a verified source that has been manufactured to meet the specifications. Use model POA-LLB02 / POA-LMP39 (service part no 610 292 4848) as your Sanyo projector lamp replacement. Resist the temptation to buy a cheaper POALLBO2 or POA-LMP39 counterfeit model as this can damage the sensitive mechanisms in your Sanyo PLCXF30/PLCXF31 projector.

 

STEP-BY-STEP INSTRUCTIONS FOR PLCXF30/PLCXF31 Lamp Replacement

Before installation

1. Check the number of POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamps to be replaced on the Lamp Status Display.
2. Turn off the projector and unplug the AC cord.
3. Allow the Sanyo PLCXF30/ PLCXF30NL/PLCXF31 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the POA-LLB02 / POA-LMP39 (610 292 4848) Lamp Assembly

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

Sanyo PLC-XF31 lamp cover, Sanyo POA-LMP39 service part no 610 292 48481. At the back of the Sanyo PLCXF30/ PLCXF30NL/PLCXF31 projector you’ll find the Lamp Hazard cover. Using a Philips screwdriver loosen the three screws that hold the cover in place. Put the cover to one side.
2. Remove the two screws on either side of each of  the POA-LLB02 / POA-LMP39 (610-292-4848) lamp. Grab the handle on the lamp cage and gently pull out each lamp. Place those lamps to one side.

3. Take the new POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamp cage by the handle and gently maneuver it into place.
Lamps for Sanyo PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, Sanyo POA-LMP39 service part no 610 292 4848

4. Avoid touching the glass or the bulb. It should slide it easily – don’t force it.
5. Tighten the screws on the Lamp Assembly.
6. Replace and tighten the three screws on either side of Lamp Hazard Cover.
7. Re-connect the power cord and turn on the Sanyo PLCXF30/ PLCXF30NL/PLCXF31 projector.

Reset Sanyo PLCXF30/ PLCXF30NL/PLCXF31 Lamp Replacement Counter

Reset the Lamp Replacement Counter only when the POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents. Lamp counter Sanyo PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, Sanyo POA-LMP39 service part no 610 292 4848

  • Turn the Sanyo PLCXF30/ PLCXF30NL/PLCXF31 projector on.
  • Press the Menu option so the On-Screen Menu will appear.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Move arrow to replace lamp number (Lamp 1 or Lamp 2) and then press Select button. The message “Lamp replace counter Reset?” will be displayed.
  • Move the pointer to YES and then press Select button.
  • Be sure to reset the correct lamp number otherwise Lamp Replace indicator continues lighting. Lamp Replacement Sanyo PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, POA-LMP39 service part no 610 292 4848
  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.
  • Do not reset Lamp Replace Counter except after the Projection Lamp has been replaced.
  • NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Cleaning your filter regularly will prolong the life of your newly installed Sanyo POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamp.

An eco-friendly alternative

Replace_Bulb_Keep_CageIf you are looking an option that is more eco-friendly and can save you some money, consider replacing only the lamp and re-using the original lamp cage. Watch our step-by-step tutorial to learn more.

Tagged with: , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-EF31NL, Sanyo POA-LMP39 service part no 610 292 4848When it’s time to change your lamp on your Sanyo PLC-EF31/PLC-EF32 projector, you’ll notice the yellow light blinking on the lamp indicator.

Be sure to use the same type of Sanyo projector lamp bought from a verified source that has been manufactured to meet the specifications. Use model POA-LLB02 / POA-LMP39 (service part no 610 292 4848) as your Sanyo projector lamp replacement.

Resist the temptation to buy a cheaper POA-LLBO2 or POA-LMP39 counterfeit model as this can damage the sensitive mechanisms in your Sanyo PLC-EF31/PLC-EF32 projector.

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLCEF31/PLCEF32

Before installation

1. Check the number of POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamps to be replaced on the Lamp Status Display.
2. Turn off the projector and unplug the AC cord.
3. Allow the Sanyo PLCEF31/PLCEF32 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the POA-LLB02 / POA-LMP39 (610 292 4848) Lamp Assembly

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

Sanyo PLC-EF31NL lamp cover, Sanyo POA-LMP39 service part no 610 292 48481. At the back of the Sanyo PLC-EF31/PLC-EF32 projectors you’ll find the Lamp Hazard cover. Using a Philips screwdriver loosen the three screws that hold the cover in place. Put the cover to one side.

2. Remove the two screws on either side of the POA-LLB02 / POA-LMP39 (service part no 610-292 -4848) lamp. Grab the handle on the lamp cage and gently pull out each lamp. Place those lamps to one side.

3. Take the newPOA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamp cage by the handle and gently maneuver it into place.
Sanyo PLC-EF31NL lamp assembly, Sanyo POA-LMP39 service part no 610 292 4848

4. Avoid touching the glass or the bulb. It should slide it easily – don’t force the lamp.
5. Tighten the screws on the Lamp Assembly.
6. Replace and tighten the three screws on either side of Lamp Hazard Cover.
7. Re-connect the power cord and turn on the Sanyo PLC-EF31/PLC-EF32 projector.

 

Reset the Sanyo PLC-EF31/PLC-EF32 Lamp Replacement Counter

Reset the Lamp Replacement Counter only when the POA-LLB02 / POA-LMP39 (service part no 610 292 4848) has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents. Sanyo PLC-EF31NL lamp replacement option, Sanyo POA-LMP39 service part no 610 292 4848

  • Turn the Sanyo PLCEF31/PLCEF32 projector on.
  • Press the Menu option so the On-Screen Menu will appear.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Move arrow to replace lamp number (Lamp 1 or Lamp 2) and then press Select button. The message “Lamp replace counter Reset?” will be displayed.
  • Move the pointer to YES and then press Select button.
  • Be sure to reset the correct lamp number otherwise Lamp Replace indicator continues lighting.Sanyo PLC-EF31 lamp replacement option, Sanyo POA-LMP39 service part no 610 292 4848
  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.
  • Do not reset Lamp Replace Counter except after the Projection Lamp has been replaced.
  • NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops blinking.

Clean your filter regularly on the Sanyo PLC-EF31/PLC-EF32 projector and you’ll prolong the life of the newly installed POA-LLB02 / POA-LMP39 (service part no 610 292 4848).

You can also prolong the life of the lamp by turning off the Sanyo PLC-EF31/PLC-EF32 projector for one hour for at least 24 hours and waiting at least five minutes before turning the projector off.

Replace_Bulb_Keep_CageSave money, save resources

If you are looking an option that is more eco-friendly and can save you some money, consider replacing only the lamp and re-using the original lamp cage. Watch our step-by-step tutorial to learn more.

Tagged with: , , , , , , , , , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group