We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 35

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Vivitek_D326MX_projector_Vivitek_5811100235_projector_lampFollow this guide to replace the Vivitek D326MX projector lamp.

Watch your hours

When the picture om screen becomes distorted or the color looks off, this is a warning sign that your Vivitek D326MX  projector lamp is reaching end of life.

Check the lamp hours when you see the power LED flashing 5 times consecutively.

Buy the right projector lamp!

Your Vivitek D326MX projector uses the Vivitek 5811116206-S projector lamp. Be sure the purchase an authentic projector lamp and avoid the temptation of a the generic lamps with their bargain prices. There are several problems associated with generics that you want to avoid and these include

Go with an authentic projector lamp and keep your Vivitek D326MX projector working properly.

Find this authentic lamp on Amazon sold by these authorized dealers:

Vivitek D326MX Projector Cage Assembly with Original Projector Bulb Inside

Step 3: Replace the projector lamp

Your Vivitek D326MX projector uses the Vivitek 5811116206-S projector lamp. Before changing the projector lamp do the following safety steps:

  • Reduce the risk of electrical shock by disconnecting the power cord on the Vivitek D326MX projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

Vivitek_D326MX_projector_Vivitek_5811100235_remove_projector_lamp

  • Turn the projector around to locate the lamp cover screw.
  • a) Remove the two captive screw holding the lamp cover place.
  • b) Remove the lamp compartment cover

Vivitek_D326MX_projector_Vivitek_5811100235_replacement_projector_lamp

  • Insert the new Vivitek 5811116206-S into the projector making sure it’s properly aligned.
  • Tighten the two screws.
  • Replace the projector lamp cover and tighten the two screws.
  • You are now ready to reset the lamp timer.

 Resetting the Lamp Hour Timer

It’s important to only reset the lamp timer when the Vivitek 5811116206-S projector lamp has been replaced. Resetting the lamp timer without changing the lamp can make it work beyond its recommended hours and cause harm to your Vivitek D326MX projector.

Vivitek_D326MX_projector_Vivitek_5811100235_res

  • Press the Menu button to open the OSD menu.
  • Press the cursor buttons to move to the Installation II menu.
  • Cursor down to the LAMP HOUR RESET option
  • Press ENTER. An on screen message appears
  • Press the cursor down arrow to reset the lamp hour to zero.
  • Press MENU to get back to the Installation II Menu.

 

Extending the life of the Vivitek 5811116206-S projector lamp:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the Vivitek D326MX projector and set to Eco Mode to reduce the amount of power used but extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Dell_1409X_projector_Dell_311-8943_725-1012_projector_lampThis easy to follow guide walks you through replacing the Dell 1409X projector lamp.

Invest in authentic!

In order for the Dell 1409X projector to keep working it needs a Dell 1409x projector lamp. Always buy authentic to keep the projector working at its best. Generic lamps should be avoided because of a variety of problems including:

Protect your health and keep your Dell 1409WX projector from being damaged. Invest in a Dell 311-8943 authentic projector lamp! Look for the seal of approval!

Find this lamp on Amazon sold by these authorized dealers:

End of projector lamp warnings

A blinking amber light on the Dell 1409X means the projector lamp is approaching end of life. You will also see the on-screen message “Lamp is approaching the end of its useful life in full power operation. Replacement suggested!”

Don’t wait too long or you may hear making a loud popping noise before the projector lamps burns. “Lamp Defective” will then show on screen and remain until a new projector lamp has been installed. The projector will eventually turn off.

 

Dell_1409X_projector_Dell_311-8943_725-1012_replace_projector_lampReplacing the Dell 1409X projector lamp

Before replacing the Dell 311-8943 (725-10120) projector lamp be sure to turn the projector off and disconnect from the AC plug. Let the projector cool down for at least 30 minutes. It should be cool to the touch. Don’t attempt to change the lamp when the projector is still hot as there is a good chance you can get severely burned.

  • Place the Dell 1409WX on a soft surface and turn in upside down to access the projector lamp cover. Loose the two screws that hold the projector lamp cover in place.
  • Loosen the two screws that secure the projector lamp.
  • Pull the projector lamp up by its metal handle. Pulling too quickly can cause the bulb to shatter. NOTE: Don’t throw the Dell 311-8943 projector lamp into regular garbage! Since it contains mercury, this lamp must be properly recycled.
  • Install the new Dell 311-8943 projector lamp making sure it is properly aligned into the projector.
  • Tighten the two screws that secure the Dell 311-8943 projector lamp.
  • Replace the projector lamp cover and tighten the two screws.
  • You are now ready to reset the lamp timer.

Reset the Dell 1409WX projector lamp counter

The Dell 1409WX projector tracks the life of the Dell 311-8943 (725-10120) projector lamp and will trigger the warning signals when it’s time to replace. Each time you replace the Dell 311-8943 projector lamp you must reset the lamp timer to zero. Failure to do so can result in you using the projector past the optimum lamp life and causing the projector lamp to explode.

Dell_1409X_projector_Dell_311-8943_725-1012_projector_lamp_hours

  • To access the Main Menu press the left or right buttons on your projector’s control panel or remote control.
  • Scroll over the the LAMP Menu. Press ENTER to access.
  • Scroll down to the Lamp Reset icon. Press ENTER.
  • Scroll down to choose YES and press ENTER to reset the projector lamp timer.

 

Tips for extending Dell 1609WX projector lamp life:

  • From the LAMP Menu, choose ECO MODE: Select On to use the projector at the lower power level of 165 Watts, which makes the Dell 1409X projector operate quieter and with lower light that gives more projector lamp life. Select off to operate at the 200 Watts power level.
  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Dell 1409X projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

Save money and go green

Dell_1409X _projector_Dell_311-8943_725-1012_replace_projector_lamp_bulb

 

Looking for a green alternative for the Dell 1409X projector? Try replacing only the projector lamp bulb and re-using the same plastic cage with the 311-8943 projector lamp. Watch our training video to see learn.

 

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Optoma GT360_projector_BL-FP180E SP.8EF01GC01_projector_lampThis guide teaches you how to replace your Optoma GT360 projector lamp.

Invest in authentic replacements

The Optoma GT360 uses a BL-FP180E (SP.8EF01GC01) specialized projector lamp that will need to be changed after 3000 hours of use.  Avoid safety and health issues and keep your projector working with an authentic Optoma GT360 projector lamp replacement.

Why avoid generics?

Find this lamp sold on Amazon by these authorized distributors:

End-of-life warnings

When the Optoma BL-FP180E (SP.8EF01GC01) projector lamp is reaching end of life, a warning sign appears on screen.

Optoma-GT360_projector_BL-FP180E_SP.8EF01GC01_projector_replacement_lamp_warning

Replace the lamp immediately when you see the warning signs. Using the lamp beyond its recommended 3000 hours can result in the lamp exploding inside the projector. This results in a messy and time consuming clean up. Watch for these other signs that the Optoma GT360 projector lamp is reaching it’s end of life:

  • the Lamp LED flashing amber
  • picture has poor colour quality
  • image vibrancy and definition has deteriorated

Installing the replacement Optoma BL-FP180E lamp

Pre-installation safety Preparation:

Follow these important safety tips before installing a new Optoma BL-FP180E into your Optoma GT360 projector.

  • Switch off the power to the projector by pressing the Power/Standby button.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. The Optoma GT360 runs at a high temperature and you can burn yourself badly if you don’t allow the projector to cool down.
  • Disconnect the power cord.

Optoma-GT360_projectors_BL-FP180E_SP.8EF01GC01_replacement_projector_lampStep-by-step instructions

Remove the old lamp

1: Use a screwdriver to loosen the two screws holding the projector lamp cover in place. The Optoma GT360 should be cool to the touch.

2: Remove the lamp cover and place to one side. Don’t lose the screws to the cover as the projector will not turn back on until the projector lamp cover has been properly installed.

3: Remove both screws holding the BL-FP180E (SP.8EF01GC01) in place.Lift the wire handle on the lamp and gently remove it from the projector. Be careful not to hit the lamp or you can cause it to break.

NOTE: The BL-FP180E (SP.8EF01GC01) contains mercury and should be properly recycled. Don’t throw into the regular garbage.

Install the new lamp:

a. Take the new Optoma BL-FP180E (SP.8EF01GC01) projector lamp out of its packaging and lift the handle on the lamp.

b. Gently place it into the projector making sure not to touch the actual bulb. Oil from fingerprint marks can burn black spots onto the lamp when it heats up.

c. Tighten the screws on the projector lamp.

d. Close the lid. Tighten the cover screws. You are now ready to reset the lamp timer.

Step 4: Reset the Optoma GT360 projector lamp timer

Your Optoma GT360 comes equipped with an automatic projector lamp timer that tracks the number of hours left for the BL-FP180E (SP.8EF01GC01) lamp. Each time you change the lamp you need to reset the lamp timer. Failure to do so may cause the projector to use the lamp over the recommended period of time resulting in the lamp exploding.

Optoma-GT360_projector_BL-FP180E_SP.8EF01GC01_projector_lamp_lamp_reset

To reset the lamp timer:

  • Press MENU
  • Select OPTIONS
  • Select Lamp Settings
  • Select Lamp Reset
  • Select Yes

TIP FOR LONGER LAMP LIFE:

Under Brightness Mode:

  • Choose STD to dim the projector lamp and lower power consumption making the lamp last longer.
  • Choose BRIGHT to make the lamp brighter but decrease lamp life.
  • Learn the TOP Tips for extending the lamp life in your Optoma EX540 projector.
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Toshiba_TDP-D1_US_projector_Toshiba-TDP-LD1-75016689_replacement_projector_lampChanging the Toshiba TDP-D1-US  projector lamp can be done in 3 easy steps. Our guide shows you how.

Step 1: Be prepared with an authentic lamp

It may be confusing trying to find the correct Toshiba TDP-D1-US projector lamp for your Toshiba TDP-D1-US projector because there are so many choices on the Internet. Your key for successful replacement lamp is to always install an OEM replacement projector lamp. Look for the seal of approval.

Avoid getting fooled into buying a counterfeit. You get want you pay for and generic, copycat lamps have a number of serious issues that include a shorter life, along with inferior prone to explosions. Copycat manufacturers have used toxic chemicals as substitutes with parts that can’t be calibrated so can damage your projector’s optics as well as your eyesight. Installing a generic lamp also voids your warranty so if your projector is damaged you’ll have to pay for the repairs yourself. For the few dollars saved buying generics, it’s not worth it. They cost you more in the end. Go with authentic.

Find this lamp sold on Amazon by these authorized dealers:

When the Toshiba TDP-D1-US projector lamp is running out of time you’ll notice the picture has poor color quality or may appear dimmer than usual. When the projector lamps reaches the end of life at 1,500 hours, the bulb icon will appear and a message “Replace your lamp” appears.

Step 3: Installing the projector lamp

Follow these important safety tips before changing the projector lamp:

  • Switch off the power to the projector by pressing the Power/Standby button.
  • After waiting 30 seconds, disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. The Toshiba TDP-D1-US projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Toshiba_TDP-D1-US_projector_Toshiba-TDP-LD1-75016689_replacement_projector_lamp

Loosen the two screws holding the lamp cover in place. and remove the lamp cover.

Loosen the three screws holding the Toshiba TDP-LD1 75016689 projector lamp in place, and pull on the handle to remove the lamp. NOTE: Recycle the burnt out Toshiba TDP-LD1 75016689 properly as these lamps do contain mercury.

Get the new Toshiba TDP-LD1 75016689 replacement lamp ready. Align the orientation, press down until the bottom is reached, and lock in place using the three lamp locking screws.

Replace the lamp cover. You are now ready to reset the lamp timer.

Reset the replacement projector lamp timer

Each time you change the lamp you need to reset the lamp timer. Failure to do so may cause the projector to use the lamp over the recommended period of 2000 hours time resulting in the projector lamp exploding.

Extend the life of the Toshiba projector lamp:

oshiba_TDP-D1_projecto_Toshiba-TDP-LD1-75016689_reset_projector_lamp_timer

  • Press the SETTING MENU button to display the menu screen.
  • Scroll down the menu options to the Lamp Time
  • Press the ENTER button to select zero.
  • Click ENTER to exit the MENU.

 

Learn more tips for extending the projector lamp life in your Toshiba TDP-D1-US projector.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

3M_MP8725B_projector_3M+78-6969-9297-9+EP7630BLK_replacement_projector_lampWhen it’s time to replace the 3M MP8725B projector lamp, this guide shows you how.

Avoid generics

In order to keep your 3M MP8725B projector working at its optimum, be sure to install a an athentic OEM 3M MP8725B projector lamp.  Generic “compatible” lamps are NOT authentic lamps and can damage the sensitive optics.

Copycat lamps have shorter lamp life than original lamps and are prone to explosions as well as exposing you to toxic materials. Even more disturbing is the lack of safeguards to protect your eyes. Invest in an authentic a 3M 78-6969-8778-9 EP2050 projector lamp. Look for the seal of approval before buying your OEM lamp.

Find this authentic lamp on Amazon sold by these authorized dealers:

 

 

End of life warning signs

When it’s time for a replacement lamp on your 3M MP8725B projector the you’ll see the change the lamp message on screen. The lamp indicator on the 3M MP8725B projector also lights red.

Warning message at 1,700 hours: CHANGE THE LAMP, AFTER REPLACING LAMP RESET THE LAMP TIMER.

Warning message at 1,979 hours: POWER WILL TURN OFF AFTER 20 more hours

A count down to zero will begin and when the number of hours reaches ZERO the projector will shut down. Replace the projector lam immediately.

Replacing the projector lamp

Before replacing the 3M 78-6969-8778-9 projector lamp, follow these safety steps

  • Wait until the projector is cool to the touch before removing the lamp. These projector work at a high temperatures and you can get badly burned.
  • Be sure to unplug the projector before replacing the lamp.

3M_MP8725B_projector_3M_78-6969-9297-9+EP7630BLK_replacement_projector_lamp

  1. The lamp access door is located on the bottom of the machine. Turn over the projector onto a soft surface. Unscrew the screw holding the screw in place. Remove the cover. Place it to one side.Unscrew the two projector lamp screw.
  2. Grasp the lamp module with one hand and the projector body with the other hand. Carefully slide the lamp module out. Being careful not to bang the lamp so it doesn’t break. Take care not to bang the actual lamp or it may break. Learn how to do a proper clean up if the lamp breaks or explodes.
  3. Insert the new 3M 78-6969-8778-9 projector lamp. Tighten the two screws on the new projector lamp. Take care not to touch the bare lamp as oil from your finger can burn black spots onto the lamp.

Reset the lamp timer

After changing the 3M 78-6969-8778-9 projector lamp you need to reset the lamp timer so the 3M MP8725B projector will turn back on. To reset:

  • Press the Reset button on the projector or Menu On button on the remote
  • When the total lamp hours are displayed, use the arrow button on the projector or the disc pad to select 0 (or CANCEL).

Extend the projector lamp life

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the 3M MP8725B projector projector projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

ViewSonic_PJD5231_projector__RLC-049_Projector_lampThis helpful guide shows you how to replace the Viewsonic PJD5231 projector lamp.

Authentic lamps are critical!

Your Viewsonic PJD5231 is a sophisticated piece of technology with sensitive optics stored inside it’s main operating system. It doesn’t make sense to buy a cheap, reproduction lamp that is inferior to authentic OEM lamps. These Original Equipment Manufacturer (OEM) lamps are created using the proper materials and with the proper fittings. Look for the seal of approval that lets you know you are buying an authentic Viewsonic PJD5231 projector lamp.

6 reasons to avoid generic lamps:

Learn how to spot the copycat lamps posing as authentic lamps.

Find this lamp on Amazon from these authorized dealers:

Replacement Warnings

When it’s time to replace the Viewsonic PJD5231 projector, you’ll notice the Power LED lamp light becomes a bright blue and Lamp LED becomes bright red. A series of warning message will start showing on screen.

ViewSonic_PJD5231_projector_RLC-049_replacement_warnings_Projector_lamp

 

1st warning: The lamp has been in operation for 3500 hours. Install a new lamp for optimal performance. If the projector is normally run with Economic selected you may continue to operate the projector until the 3950 hour lamp warning appears.

 

2nd warning: The lamp has been in operation for 3950 hours. A new Viewsonic RLC-055 projector lamp should be installed so the projector doesn’t run out of lamp time.

 

 

3rd warning: The lamp has been in operation for 4000 hours. Replace it immediately especially if you notice diminished light and poor picture quality.

 

 

Final warning: The Viewsonic RLC-055 projector lamp The lamp MUST be replaced before the projector will operate normally.

Installing the Viewsonic RLC-055 lamp

ViewSonic_PJD5231_projector_replace_RLC-049-Projector-LampBefore replacing the Viewsonic RLC-055 projector lamp follow these crucial safety tips to prevent injury to yourself or the projector:

  • NEVER change the lamp unless the Viewsonic PJD5231 projector is cool to the touch. The PJD5231 operates under extremely high temperatures and you can burn yourself quite badly.
  • Switch off the power to the Viewsonic PJD5231 projector.
  • Disconnect the power cord.

Use a screwdriver to undo the screw holding the lamp cover in place. Remove the lamp cover, being careful not to lose the screws.

Slide the lid — slowly — off the projector. and place to one side. Don’t lose the lid because the Viewsonic PJD5231 projector will not turn back if the lamp cover hasn’t been installed properly.

Remove the two screws holding the Viewsonic RLC-049 lamp in place.

Note: The used Viewsonic RLC-049 lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

 

 

ViewSonic_PJD5231_projector_insert_replacement_RLC-049_projector_lamp

Pull out the lamp connector from a slot in the lamp compartment. Disconnect it

Grab the Viewsonic RLC-055 projector lamp by the wire handle and slowly pull it out of the projector. Be careful not to bang the lamp against the projector as this may case the bulb to break.

ViewSonic_PJD5231_projector_disconnect_RLC-049-Projector-Lamp

Learn what to do if the lamp has exploded inside the projector.

  • Insert the new lamp into the lamp compartment and make sure it fits in the projector. Reconnect the lamp connector and place it back into its slot to be flush with the projector
  • Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Viewsonic PJD5231 projector.
  • Tighten the two screws on the lamp.
  • Replace the lamp cover and tighten its two screws. Reset the lamp timer.

Reset the Lamp Replacement Timer

The Viewsonic PJD5231 projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. Each time you install a new lamp, you’ll need to to reset the lamp timer to know how many hours are left and when to change the bulb.

To reset the Lamp Replacement Timer:

placement_projector_lamp

  • After the startup logo, open the On-Screen Display (OSD) menu.
  • Go to the SYSTEM SETUP: Advanced Lamp Settings menu.
  • Press MODE/ENTER to display the Lamp Settings page.
  • Press to highlight Reset option.
  • Press MODE/ENTER.
  • A warning message is displayed asking if you want to reset the lamp timer.
  • Highlight the Reset option
  • The lamp time will be reset to ‘0’.

Extend the life of the Viewsonic RLC-055 projector lamp by setting the Viewsonic PJD5231 to Eco Mode. This lowers the brightness of the projector and makes the lamp last longer. Read about other tips for extending the lamp life in your Viewsonic PJD5231.

 

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_EMP-755-Epson_ELPLP32_projector_lamp_timerLearn how to replace the Epson EMP-755 projector lamp in three simple steps.

Step 1: Go with authentic

Your Epson EMP-755 needs a Epson ELPLP32 projector lamps. The Internet has been flooded with copycat manufacturers who create generic imitations and the challenge is to find an authentic projector lamp. Save yourself unnecessary headaches and keep your warranty intact for your Epson EMP-755 projector. Look for the seal of approval and buy an authentic Epson EMP-755 projector lamp.

Reasons to avoid counterfeit lamps:

Learn the 7 Ways to Spot a Counterfeit Lamp.

Find this lamp on Amazon sold by these authorized dealers:

Step 2: Watch for end of life signs

Epson_EMP-755-765C_Epson_ELPLP32_projector_lamp_ warningTrack the umber of hours left in the Epson EMP-755 projector by going to the Info menu found on the Main menu. The Epson ELPLP32 projector lamp will last up to 2000 hours if the Brightness setting is on normal. Change the setting to low and get up to 3000 hours. Watch for these signs as well to let you know the end of life is coming for the Epson ELPLP32 lamp:

  • The lamp warning light on the projector starts flashing orange. If it turns red and stays red, replace the Epson ELPLP32 projector lamp immediately.
  • Imaged becomes dark, colours are off or appear to be deteriorating
  • A message saying “Replace the lamp” appears on screen.

Install the new Epson ELPLP32

Installation will take under 10 minutes but before installing the new Epson ELPLP32 projector lamp into the Epson EMP-755 projector, be sure to follow these preparation steps:

Epson_EMP- 755-765c_unplug_ELPLP32_projector_lamp

  • Turn power button off and wait for the power light to stop flashing.
  • Unplug the power cord from the Epson EMP-755 projector.
  • The Epson EMP-755 should be cool to the touch before you try to change the Epson ELPLP32 projector lamp. This projector operate at a high temperatures so you can burn yourself badly if you don’t allow for the cool down period.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Epson_EMP-755_remove_cover_Epson_ELPLP32_projector_lamp

  • Turn the Epson EMP-755 over and placing on a soft, scratch free surface.
  • Press on the tabs located on top of the Epson EMP-755 cover. Lift up the lamp cover.

Epson_EMP-755-remove_Epson_ELPLP32_projector_lamp

  • Using the screw driver provided with the Epson EMP-755 projector, loosen the two screws holding the Epson ELPLP32 projector lamp in place.

Epson_EMP- 755-remove_projector_lamp_ELPLP32Pressing on the indents on the sides of the Epson ELPLP32, pull the projector lamp gently up out of the Epson EMP-755 projector. Take care not to bang the actual lamp or it may break. Learn how to do a proper clean up if the lamp breaks or explodes.

NOTE: The Epson ELPLP32 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps and be good to the environment.
Epson_EMP-755_change_air_filter_ELPLP32_projector_lamp

  • Gently place the new Epson ELPLP32 lamp into the Epson EMP-755 making sure not to touch the actual bulb. The oil on your fingers will leave a burn mark on the lamp once it heats up and this can cause black out spots on the screen.
  • Tighten the screws on the new Epson ELPLP32 lamp.
  • Slide the air filter out and remove it immediately. Slide in the new filter that came with the Epson ELPLP32 lamp. Replace the lamp cover.
  • You are now ready to reset the lamp timer.

 

Reset the lamp timer in the Epson EMP-755

Your Epson EMP-755 has a built-in timer to track the life of the Epson ELPLP32 projector lamp. So, it’s very important that you reset the lamp timer every time you replace the Epson ELPLP32 projector lamp. Here’s how:

Epson_EMP-755_reset_projector_lamp_timer

 

  • Press the MENU button on either the remote control on the projector’s control panel.
  • Scroll down to the RESET option.
  • Press Enter. The RESET ALL screen will appear.
  • Scroll down to LAMP-HOURS RESET.
  • Press ENTER to open up the confirmation screen

Epson_EMP-755_reset_lamp_timer_screen2_Epson_ELPLP32_proejctor lamp

  • Highlight YES.
  • Press ENTER.
  • Press ESC or MENU to exit this option.

Congratulations! You’ve just installed at new Epson ELPLP32 projector lamp in your Epson PowerLite 755c.

Tips for a longer lasting Epson ELPLP32 projector lamp:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP-755 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

ukane_ImagePro_8769_Dukane_456-8767A_replacement_projector_lampThis guide shows you how to change the Dukane ImagePro 8769 projector lamp in three easy steps.

Step 1: Know when to replace

You can expect up to 2100 hours (up to 3100 hours in Eco mode) from your Dukane ImagePro 8769 projector lamp. When it time to replace the Dukane ImagePro 8769 projector lamp, you may notice a faded image or colors that are not correct. Replace the projector lamp immediately when you see the message : “The lamp has reached the end of its usable life. Please replace the lamp.”

DO NOT KEEP USING THE FINISHED LAMP when it has reached end of life. If  you continue using the projector lamp beyond the recommended times, Dukane ImagePro 8769 will go into standby mode.  Press the HELP button on the remote control for 10 seconds to reset the lamp timer to zero and replace the projector lamp immediately. 

Step 2: Invest in authentic

There are plenty of online stores selling Dukane ImagePro 8769 projector but the most important thing is to buy an authentic OEM lamp. If the price seems too good to be true or much lower than normal, you’re buying a knock-off lamp. Keep your projector working by investing in an authentic.

Find this lamp on Amazon from these authorized dealers:

 

Reasons to avoid generics:

Step 3: Replacing the projector lamp

The Dukane ImagePro 8769 projector uses the Dukane 456-8767A projector lamp. Before installing a new projector lamp do the following safety steps:

  • Reduce the risk of electrical shock by disconnecting the power cord on the projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes. It should be cool to the touch.

Dukane_ImagePro_8769_Dukane_456-8767A_remove_projector_lamp_cover
Protect the Dukane ImagePro 8769 projector’s top surface by placing it face down on a soft surface. Turn the projector over and loosen the screws on the lamp cover.

Use a Philips screwdriver to push and release the tab. Push up and remove the lamp cover. NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.

Dukane_ImagePro_8769_Dukane_456-8767A_remove_projector_lamp-2

Loosen the two screws securing the Dukane 456-8767A projector lamp. The screws are not removable so will start start freewheeling. Remove the lamp by grabbing onto the indents on the lamp and pulling up.

Never force the lamp out; pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Dukane 456-8767A projector lamp projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Dukane_ImagePro_8769_Dukane_456-8767A_install_replacement_projector_lamp

Gently put in a new Dukane 456-8767A projector lamp and tighten the two screws to hold the lamp in place. Make sure the screws are secure as a loose screw can cause a bad connection while a over tightened screw may cause the lamp to notwork.

Dukane_ImagePro_8769_Dukane_456-8767A_cover_projector_lamp-4

Replace the lamp cover on the projector.

Slip the lamp cover back until it snaps into place.

Restart the projector to reset the lamp timer.

Resetting the lamp timer

It’s important to set the lamp timer so the Dukane ImagePro 8769 can accurately track the life of the newly installed Dukane 456-8767A projector lamp.
Dukane_ImagePro_8769_Dukane_456-8767A_set_projector_lamp_timer
To reset the lamp timer go to the Dukane ImagePro 8769 Default Menu. Scroll down to Clear Lamp Hour Meter to reset the lamp timer.

Extend the life of the Dukane 456-8767A projector lamp:

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Toshiba_TDP-D1_projecto_Toshiba-TDP-LD1-75016689_replacement_projector_lampChanging the projector lamp in the Toshiba TDP-D1 is as easy as 1-2-3!

Step 1: Know when to replace the lamp

When the Toshiba TDP-D1 projector lamp is running out of time you’ll notice the picture has poor color quality or may appear dimmer than usual. When the projector lamps reaches the end  of life at 1,500 hours, the bulb icon will appear and a message “Replace your lamp” appears.

Step 2: Buy an authentic projector lamp

Your Toshiba TDP-D1 uses the Toshiba TDP-LD1 75016689. It may be confusing trying to find the correct projector lamp since there are so many choices. It’s avoid getting duped into buying a counterfeit  lamp posing as an authentic lamp. Always look for the seal of approval and watch for telltale signs you are about to purchase a counterfeit lamp:

Find this lamp sold on Amazon by these authorized dealers:

Step 3: Installing the projector lamp

Follow these important safety tips before changing the projector lamp:

  • Switch off the power to the projector by pressing the Power/Standby button.
  • After waiting 30 seconds, disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. The Toshiba TDP-D1 projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Toshiba_TDP-D1_projector_Toshiba-TDP-LD1-75016689_replacement_projector_lamp

Loosen the two screws holding the lamp cover in place. and remove the lamp cover.

 

Loosen the three screws holding the Toshiba TDP-LD1 75016689 projector lamp in place, and pull on the handle to remove the lamp. Recycle the burnt out Toshiba TDP-LD1 75016689 properly as these lamps do contain mercury.

Get the new Toshiba TDP-LD1 75016689 replacement lamp ready. Align the orientation, press down until the bottom is reached, and lock in place using the three lamp locking screws.

Replace the lamp cover. You are now ready to reset the lamp timer.

Reset the replacement projector lamp timer

Each time you change the lamp you need to reset the lamp timer. Failure to do so may cause the projector to use the lamp over the recommended period of 2000 hours time resulting in the projector lamp exploding.

Extend the life of the Toshiba projector lamp:

oshiba_TDP-D1_projecto_Toshiba-TDP-LD1-75016689_reset_projector_lamp_timer

  • Press the SETTING MENU button to display the menu screen.
  • Scroll down the menu options to  the Lamp Time
  • Press the ENTER button to select zero. 
  • Click ENTER to exit the MENU.

 

Learn more tips for extending the projector lamp life in your Toshiba TDP-D1 projector.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Christie_DS+65_projector_Christie_003-000884-01_replacement_projector_lampConsult our handy guide to install a new projector lamp in your Christie DS+65 projector.

The importance of an authentic projector lamp

The best way to keep your Christie DS+65 projector working properly is to always install an authentic replacement projector lamp. You may be tempted to buy a generic lamp sold at discount prices. These projector lamps actually cost more since the have a much shorter life and are prone to explosions. There are health and safety concerns as well, since these lamps have been created with carcinogenic, toxic substitutes. Installing a generic Christie DS+65 projector lamp voids your warranty.

Buy this lamp on Amazon sold by these authorized dealers:

Christie DS+65 projector lamp end of life warnings

Christie_DS+65_projector_Christie_003-000884-01_reset_projector_lamp_timerYour Christie DS+65 projector uses two the Christie 003-000884-01 projector lamp. When it has reached the LAMP indicator on the projector will light red. Replace the projector lamp immediately when you see this. Other warning signs may be a dim picture, colour that appears washed and a image that is fading.

Replacing the projector lamp

The Christie DS+65 projector is fitted with two individual projection lamps. Using the Lamp Sub-Menu, you can select a dual or single lamp mode. The lamps can also be replaced separately as needed. Eco-mode reducing the power for longer lamp life.

Before changing the projector lamp:

  • Allow the Christie DS+65 projector to cool down for at least 45 minutes. This projector operates at an extremely high temperature and you can get burned. Don’t rush it.
  • Unplug the electrical cord so there is no chance the projector could get turned on during the installation. This could damage your projector and also give you a shock.

To replace the projector lamp:

Christie_DS+65_projector_Christie_003-000884-01_replace_projector_lamp

  • Loosen the two screws on the Christie DS+65 lamp cover. Open the cover
  • Loosen the three screws on Lamp 1 andpull out the used Christie 003-000884-01 projector lamp assembly by using the built in handle.
  • NOTE: The used Christie 003-000884-01 projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.
  • Pulling too quickly can cause the bulb to shatter. Learn what to do if the lamp breaks.
  • Replace the lamp assembly with a new Christie 003-000884-01. Be careful not to touch the actual bulb as oil from your fingers can leave black marks on the lamp. If you are replacing only one lamp, be sure not to touch the remaining lamp
  • Tighten the three screws on the replacement lamp.
  • Put back the lamp cover and tighten its two screws.
  • Connect the AC power cord to the Christie DS+65 and turn on the projector to reset the lamp timer.

Tips for longer projector lamp life:

  • Avoid frequent on and offs to avoid power surges.
  • Don’t let the projector overheat as this puts stress on the lamp. Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Let the projector stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Keep the air filters clean and free of dust so it can do its job and keep the projector lamp for overheating.
  • Eco mode reduces lamp brightness while extending the lamp life.
  • Learn more with Top tips for extending projector lamp life.
Tagged with: , , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group