We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 46

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

NEC_NP-M260W_projector_NP15LP_projector_lampWhen it’s time to replace the NEC NP-M260W projector lamp, this quick guide can help.

Be ready with an authentic lamp

In order to keep your NEC NP-M260W projector working at it’s best, always install an OES NEC NP-M260W projector lamp. Despite their tempting bargain prices, generic projector lamps should be avoided. They’ve been created with substandard toxic materials (including the carcinogenic  Krypton-85) making them prone to explosions. Installing them often damages the sensitive electronics in your NEC NP-M260Wprojector and to top it all off they have a shorter life! Save yourself the hassle and buy authentic!

Find this lamp sold on Amazon by these authorized dealers:

When to replace the projector lamp

Watch for the following signs that indicates the NEC NP15LP projector lamp is reaching end of life and needs to be replaced:

  • message on screen reads LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.
  • the LAMP indicator begins to blink red
  • colour looks off
  • picture is faint or has deteriorated

NEC_NP-M260X_check_NECNP15LP_projector_lamp_usageTrack the life of the NEC NP15LP projector lamp from the Usage Time menu.

  • Go to INFO menu
  • Scroll down to USAGE TIME to display the LAMP LIFE REMAINING and LAMP HOURS USED.
  • The progress indicator shows the percentage of remaining bulb life:
  • When the lamp usage reaches 0, the Lamp Life REMAINING starts a count down from 100 hours
  • When the count down reaches 0, the projector will turn off and not turn on.

Changing the NEC NP15LP projector lamp

NOTE: New air filters are shipped with the lamp and it’s recommended you replace them at the same time.

Follow these important safety instructions before installing the new NEC NP15LP projector lamp

  • turn off the NEC NP-M260W projector.
  • unplug the projector from its power source.
  • unplug the power cable.
  • wait until the projector is cool to the touch to avoid getting burned.

NEC_NP-M260W_NEC_NP16LP_projector_lamp_remove_lamp_screwLoosen the NEC NP-M260W projector lamp cover screw.

NEC_NP-M260W_projector_lamp_NEC_NP16LP_remove_lamp_cover

Push and slide the NEC NP-M260W projector cover off.

NEC_NP-M230W_remove_NEC_NP16LP_projector_lamp_screws

Loosen the two screws holding the NEC NP15LP projector lamp in place. (The screws will not come out only loosen.)

NEC_NP-M260W_remove_NEC_NP16LP_projector_lamp

 

Remove the projector lamp by holding the indent and pulling up.

NOTE: Your NEC NP15LP lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

NEC_NP-M260W_projector_lamp_install_new_NEC_NP16LPInstall a new lamp housing into the NEC NP-M260W projector, gently pressing the projector lamp housing into the socket. Take care not to touch the actual bulb as your finger prints can leave oil marks that burn black marks onto the bulb.

NEC_NP-M230W_projector_tighten_NEC_NP16LP_projector_lamp_screws

Push the top center on the projector lamp to secure it. Tighten the screw on the projector lam

NEC_NP-M230W_projector_replace_lamp_cover_NEC_NP16LP_projector_lamp

Re-attach the NEC NP-M230W lamp cover by sliding the cover until it snaps into place. Tighten the screw on the lamp cover.

Replacing the filters

There are four filters in the NEC NP-M260W projector:

  • Honeycomb hard filter – large and small
  • Accordion soft filter — large and small

Replace all four filters at the same time. Before replacing the filters wipe off any dust and dirt that came loose from the old filters. NOTE: The filters are made with two different types of material in the membrane. Both perform the same.

NEC_NP-M260W_projector_lamp_NEC_NP16LP_remove_air_filterPush the catch to release the NEC NP-M260W filter and gently pull it out.

 

NEC_NP-M260W_projector_lamp_NEC_NP16LP_detach_filter_cover

The filter cover is fixed at six separate points in the projector. Bow the filter cover by pushing it slightly until it releases.

 

NEC_NP-M260W_projector_lamp_NEC_NP16LP_replace_dark_filtersRemove the dark sponge filter and clean the filter unit and cover. Attach the new non-woven white material filters.

NEC_NP-M260W_projector_lamp_NEC_NP16LP_replace_four_filters

  • Filter unit: Attach two honeycomb hard filters to the NEC NP-M260W filter unit.
  • Filter cover: Attach the two accordion soft filters to the filter cover. Be sure to align the accordion slits with the protrusions of the filter cover.

 

NEC_NP-M260W_projector_lamp_NEC_NP16LP_attach_filter_coverAttach the filter cover back to the filter unit. Align the filter until with the filter cover and push the protrusions into place. Make sure all the six mounting points are aligned properly.

 

NEC_NP-M260W_projector_lamp_NEC_NP16LP_attach_filter

Insert the two catches of the top of the filter into the groove of the cabinet. Push the filter until it clicks into place.

 

Reset the lamp timer

Once the NEC NP15LP projector lamp and NEC NP-M260W projector filter have both been replaced you will need to reset the timer for both. You want the projector to be able to accurately track the projector lamp life.

NEC_NP-M260W_projector_lamp_NEC_NP16LP_lamp_timer

Clear usage hours and reset hours

  • Plug in the power cored into the wall outlet.
  • Turn on the projector.
  • From the MENU select RESET.
  • Choose CLEAR LAMP HOURS.
  • A confirmation message appears.
  • Select YES.

Reset the filter hours:

  • Scroll up to CLEAR Filter HOURS.
  • A second submenu will appear.
  • Select YES. Press the ENTER button.

Extending the life of the NEC NP15LP projector lamp

Get your newly installed NEC NP15LP lamp will last longer by choosing the ECO option. The ECO MODE increases projector lamp life by lowering the power consumption. There are three modes to choose from:

  • Auto Mode: 4000 hours
  • Normal: 5000 hours
  • Eco ModeL 8000 hours

Learn more tips to extend the life of the NEC NP15LP lamp.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_PowerLite 1260_projector_Epson_ELPLP58_projector_lampThis handy guide will help you install a new pEpson PowerLite 1220 projector lamp.

Buy an authentic Epson PowerLite 1220 projector lamp from a recognized OEM dealer. You may be tempted to buy a cheaper generic lamp in order to save money. While these knock-off lamps appear to be a bargain, they will actually end up costing you more money in the long run for the following rules:

Find this lamp on Amazon sold by these authorized dealers:

End of warning signs

Epson_PowerLite_1220_projector_Epson_ELPLP58_check_projector_lamp_hoursWhen you see the projector lamp indicator flashing orange, it’s time to change the Epson PowerLite 1220 projector lamp is reaching end of life. You may also see the Replace the lamp message on screens. Other indications are screen gets darker or starts deteriorate altogether.

Epson_PowerLite_1220_projector_Epson_ELPLP58_projector_lamp_lamp_warning In order to maintain projector brightness and image quality, replace with a new Epson LPLP58 (V13H010L58) projector lamp as soon as possible.

The Epson PowerLite 1220 projector lamp can last for close to 4,000 hours when the power consumption is set to NORMAL and up to 5,000 hours if the ECO option is used. You can check the hours left on the ELPLP58 (V13H010L58) projector lamp from the INFO Menu access off the Main Menu.

Installing a new ELPLP58 (V13H010L58) projector lamp

Before replacing the ELPLP58 (V13H010L58) projector lamp follow these important safety rules:

  1. Always unplug the power cord on the Epson PowerLite 1220 projector before replacing the projector lamp.
  2. This projector operates using high temperature. Wait at least 60 minutes before replacing the lamp so you don’t run the risk of getting burned.
  3. Never touch the bare projector lamp bulb as the oil from your fingers will burn black marks onto the projector lamp when it heats up.
  4. Never operate the Epson PowerLite 1220 projector with the projector lamp removed.

Epson_PowerLite_1220_projector_Epson_ELPLP58_remove_projector_lamp_cover

Remove the projector lamp cover screws and place to one side.

Epson_PowerLite_1220_projector_Epson_ELPLP58__remove_projector_lamp_screwsLoosen the two screws holding the Epson ELPLP58 (V13H010L58) projector lamp in place (you can’t remove them).

Epson_PowerLite_1220_projector_Epson_ELPLP58_install_new_projector_lamp

Gently lift out the Epson LPLP58 projector lamp taking care not to bang it against the projector. NOTE: The LPLP58 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

Gently insert the new Epson LPLP58 projector lamp. Make sure it fits into the Epson PowerLite 1220 projector properly. (Check that it’s facing the right way.) Tighten the Epson LPLP58 projector lamp.

You can know reset the lamp timer.

Reset the lamp timer

Epson_PowerLite_1220_projector_Epson_ELPLP58_reset_projector_lamp_timer

After you replace the lamp, you need to reset the Epson PowerLite 1220 projector lamp timer using the projector’s menu system.

  • Press the MENU button on the remote control or on the projector’s control panel. You see the main menu.
  • Select the RESET menu. Press ENTER.
  • Scroll down to select RESET LAMP HOURS. Press ENTER.
  • A prompt filed appears asking if you want to reset the lamp timer. Select YES. Press ENTER.
  • Press MENU to exit.

Longer life for the ELPLP58 (V13H010L58) projector lamp

Extend the life of the Epson ELPLP58 (V13H010L58) projector lamp with the following tips:

  • Set the Power Consumption to ECO option.
  • Clean the air filters regularly so the Epson PowerLite 1220 projector doesn’t overheat.
  • Make sure there is enough airflow around the projector.
  • Turn it off when it’s not in use.
  • Learn more: Top tips for extending DLP projector lamp life.
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Boxlight_Phoenix_S25_Boxlight_PHOENIXS25-930_projector_lampWhen your Boxlight Phoenix S25 projector lamp reaches end of life, use this guide to help you make the change.

Warning messages

When the Boxlight Phoenix S25 projector lamp is reaching its end of life, the Power LED flashing consecutively five times at the same time the Ready LED flashes once. You may also be approaching end of life with the projector lamp when you see the image becoming darker or the color becoming unnatural. Change the projector lamp immediately when any of these symptoms happen.

Get the right projector lamp

Your Boxlight Phoenix S25 projector is a sophisticated machine with high-end optics. An OEM Phoenix S25-930 Projector lamp has been designed to work closely with your projector. It’s been created with highly specialized materials and calibrated to your machine. Generic lamps are tempting to buy since they promise savings. Unfortunately they can’t deliver. When you buy generic lamps are getting something that can damage the optics in your projectors has well as exposing you to carcinogenic toxic substitutes. Generic lamps also have shorter lives and are prone to explosions. Protect your investment and purchase an authentic projector lamp.

Find this lamp on Amazon sold by these authorized dealers:

Replacing the Phoenix S25-930 projector lamp

Before replacing the Phoenix S25-930 follow these safety tips:

  • Disconnect the power cord on the Phoenix S25 projector
  • Reduce the risk of severe burns by allowing the Phoenix S25 projector to cool for at least one hour. These projectors operate using high temperatures and you run the risk of severe burns if you don’t allow it to cool down.

Boxlight_Phoenix_S25_Boxlight_PHOENIXS25-930_projector_lamp_remove_lampBoxlight_Phoenix_S25_Boxlight_PHOENIXS25-930_projector_lamp_loosen_cover_screws

  • Loosen the two top screw holding the lamp cover in place.
  • Open the projector cover.
  • Remove the two screws holding the Phoenix S25-930 projector lamp in place.
  • NOTE: Be sure to recycle the projector lamp as contains mercury and should not be thrown into regular garbage. Recycle it!Boxlight_Phoenix_S25_Boxlight_PHOENIXS25-930_projector_lamp_install_replacement
  • Insert the new Phoenix S25-930 and avoid touching the actual bulb as this can result in black spots from the oil on your hands.
  • Tighten the two screws on the Phoenix S25-930 projector lamp
  • Place the cover back onto the Boxlight Phoenix S25 projector and tighten the lamps screw. You must now reset the lamp timer.

Resetting the Boxlight Phoenix S2 lamp counter

Boxlight_Phoenix_S25_Boxlight_PHOENIXS25-930_projector_lamp_reset_timerOnce the PhoenixS25-930 projector lamp has been replaced, you will need to reset the lamp counter so the Phoenix S25 projector can accurately track the number of lamp hours remaining:

  • Turn the projector on.
  • Press the MENU button. The ON-SCREEN MENU will appear.
  • Press the POINT LEFT/RIGHT buttons to move across the top menu. Select STATUS.
  • Press the POINT DOWN button and scroll down to LAMP HOUR. Press ENTER.
  • Lamp hours will be set to zeto.

Extend the life of the Phoenix S25-930 projector lamp by always keeping the air filters clean so the projector doesn’t overheat. The Eco modes for the lamp setting uses less power by decreasing lamp brightness and extending lamp life.  Read more with Top tips for extending DLP projector lamps.

Interested in a green alternative?

Boxlight_Phoenix_S25_Boxlight_PHOENIXS25-930_ecofriendly_projector_lamp_install_replacement

With the Phoenix S25 projector  you also have the option of  just replacing the actual bulb to re-use the plastic cage. This reduces waste and is a great way to green your projector. Watch our training video to learn more.

 

 

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Optoma_HD600X_Optoma_BL-FU185A_SP.8EH01GC01_projector_lampChanging the old lamp for a new Optoma HD600X projector lamp doesn’t have to get complicated. Use our guide to get yours installed.

Buying the right lamp

Purchase your Optoma HD600X projector lamp ahead of time and be prepared. The Optoma HD600X projector uses the Optoma BL-FU185A projector lamp Be sure to purchase an authenticAvoid counterfeit lamp for the following reaons;

Spot the counterfeit.

Find this lamp sold on Amazon by these authorized dealers:

When to replace the projector lamp

Your Optoma HD600X projector uses the Optoma BL-FU185A projector lamp . When the projector lamp is approaching end of life, you may notice the Lamp-LED light flashing red or the picture quality starting to get poor resolution with washed out colours.

As the projector lamp approaches end of life, the projector lamp replacement message flashes on screen. Change your proejctor lamp immediately. The projector will not work if the lamp has burnt out or broken.

If you hear a loud pop when turning on the projector, the Optoma BL-FU185A projector lamp has broken. Learn what to do if the lamp has exploded inside the projector.

Optoma_HD600X_replace_Optoma_BL-FU185A_projector_lampInstalling the Optoma BL-FU185A projector lamp

Before replacing the Optoma BL-FU185A projector lamp follow these important safety tips:

  • Switch off the power to the HD600X projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

 

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma HD600X projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A  in place.

Note: The used Optoma BL-FU185A projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

4. Lift up the wire handle on the Optoma BL-FU185A  projector lamp and slowly remove it from the projector.

Be careful not to bang the projector lamp against the projector as this may case the bulb to break. Learn how to clean up a broken projector lamp.

5. Remove the new Optoma BL-FU185A projector lamps from its packaging. Without touching the actual bulb, lift up the handle on the new lamp and gently insert.

6. Tighten the two screws on the lamp.

7. Replace the lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.

Reset the Lamp Replacement Timer

The Optoma HD600X projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

Optoma_EW536_lamp_control_menu_Optoma_BL-FU185A To reset the Lamp Replacement Timer:

  • Turn on the projector.
  • Using the remote press MENU
  • Select OPTIONS
  • Select LAMP SETTINGS
  • Select LAMP RESET
  • Select YES.
  • Press MENU to exit.

Tips for extending Optoma BL-FU185A (SP.8EH01GC01) lamp life:

  • Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Optoma HD600X projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

Green your Optoma HD600X projector

Optoma-BL-FU185A_replacement_bulb_training_videoThe Optoma HD600X projector has the option of re-using the existing lamp cage and replacing only the actual bulb. You recycle and reduce waste this way. Watch our Optoma BL-FU185A training video to learn more.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Canon_LV-X4_projector_Canon_LV-LP21_projector_lampDon’t panic when it comes time to replace your Canon LV-X4 projector lamp.  Our step-by-step guide will help you get the job done.

Be ready with the right lamp

Your Canon LV-X4 projector uses the Canon LV-LP21 (9923A001).  In order to keep your projector working at its best you should always invest in an authentic Canon LV-X4 projector lamp. Look for the seal of approval. While generics do have a lower price tag, in the end they cost you more money due to:

Simplify your life and buy an authentic projector lamp. Still not sure about generics? Learn the 7 ways to avoid them.

Find this lamp sold on Amazon by these authorized dealers:

End of lamp life warnings

Canon_LV-X4_projector_Canon_LV-LP21_projector_lamp_indicator

When the Canon LV-LP21 projector lamp has reached its end of life the LAMP REPLACE on the projector will light yellow. Replace the lamp immediately when you see this.

Other warning signs may be a dim picture, color that appears washed and an image that is fading.

Replace the Canon LV-LP21 projector lamp

Before changing the projector lamp:

  • Let the Canon LV-X4 cool down for at least 45 minutes. This projector operates at an extremely high temperature and you could get badly burned if it’s still hot. Don’t rush it.
  • Be sure to unplug the electrical cord so there is no chance the projector could get turned on during the installation. This could damage your projector.

Canon_LV-X4_projector_Cano_-LV-LP21-9923A001_projector-lamp

  • Loosen the two screws holding the projector lamp cover in place. Place the cover aside.
  • Loosen the two screws and pull out the Canon LV-LP21 (9923A001) lamp assembly by using the built in handle.
  • NOTE: The used LV-LP21 projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.
  • Pulling too quickly can cause the bulb to shatter. Learn how to clean up a broken lamp.
  • Replace the lamp assembly with a new Canon LV-LP21. Be careful not to touch the actual bulb as oil from your fingers can leave black marks on the lamp.
  • Tighten the two screws on the lamp.
  • Put back the lamp cover and tighten its two screws.
  • Connect the AC power cord to the Canon LV-LP21 (9923A001) and turn on the projector to reset the lamp timer.

Resetting the lamp timer counter

After replacing the Canon LV-LP21 (9923A001) projector lamp, you’ll need to turn off the LAMP REPLACE indicator by resetting the LAMP REPLACE COUNTER. The counter tracks the number of hours the lamp the Canon LV-X4 projector has been used and triggers the warning light when the lamp is reaching its end of life. Not resetting it after may stop your projector from turning back on.

Canon_LV-X4_projector_Canon_LV-LP21_reset_projector_lamp_tracker

  • Turn the projector on and press the MENU.
  • The On-Screen menu will be displayed on the left.
  • Using the arrow buttons, mover the red frame pointer to the SETTING menu icon.
  • Press the up/docwn buttons, move to the LAMP COUNTER option.
  • Press OK to open up as the RESET LAMP COUNTER box.
  • Click on the SET option to open a confirmation window.
  • The message “Lamp replace counter reset?” is displayed.
  • Click on YES.
  • Press OK.
  • The lamp hours will be reset to zero.

Go green, save money

Canon_LV-X4_projector_bulb_only_Canon_LV-LP21_reset_projector_lamp_tracker

 

If you would like to save some money try replacing only the Canon LV-LP21 (9923A001) bare lamp rather than the entire lamp unit. You recycle the plastic cage and reduce waste. Watch our training video.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

anasonic_PT-D5500U_projector_Panasonic_ET-LAD55_projector_lampInstall a new Panasonic PT-D5500U projector lamp following these instructions.

Be ready with an authentic projector lamp

With the Internet flooded with so many copycat manufacturers, it can be a challenge to find the best Panasonic PT-D5500U projector lamp to use. Always look for the seal of approval, be suspicious of bargain prices and always buy from an OEM manufacturer.

6 reasons to avoid generics:

Find this lamp sold on Amazon by these authorized dealers:

When to replace the projector lamp

This projector is equipped with three indicators lamp to show when the Panasonic ET-LAD55 lamp needs replacement. These lamps flash or light up to indicate a problem or when the projector lamp has reached its end of life.

Projector lamp life with the Panasonic PT-D5500U may vary depending on the working conditions and settings. When the projector lamp being used reaches 1300 hours, the lamp monitor (LAMP1 or LAMP2) light up to the standby state. The on-screen appears for about 30 seconds recommending replacing the projector lamp. After 1500 hours, the on-screen indication will stay on the screen unless the MENU button is pushed.

A message REPLACE THE LAMP will appear on screen as well. If your Panasonic ET-LAD55 projector lamp unit is not replaced after the warning message, the projector enters a standby state. It will remain in standby state until the projector lamp is changed.

Replace the Panasonic ET-LAD55 projector lamp

Follow these important safety tips before replacing the Panasonic PT-DW5600U projector lamp:

  • Press the POWER OFF button
  • Select OK using the right or left arrows on the control panel. Press the ENTER button. (Or press the POWER OFF button again. The power indicator will light up orange.
  • Wait until the power indicator turns red and the cooling fans stop running.
  • Press MAIN POWER to OFF.

Projector lamp installation steps:

Panasonic_PT-D5500U_projector_replace_Panasonic_ET-LAD55Using a Phillips screwdriver, remove the screw securing the projector lamp cover. Slide the lamp unit cover toward the left to remove it. (See diagram #2)

Remove the two screws securing the fan unit. (See diagram #3)

Gently open the fan unit in front of the both Panasonic ET-LAD55 projector lamps. (See diagram #4)

Remove the screws holding the Panasonic ET-LAD55 projector lamp in place. (Each lamps has two screws. Take hold of the wire handle and gently remove the projector lamp. (See diagram #5)

NOTE: The Panasonic ET-LAD55 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this projector lamp!

Install the new lamp unit taking care not the touch the actual project lamp bulb as oil from your fingers will remain on the bulb and burn black spots when the projector lamp heats up.

Use a Phillips screwdriver to securely tighten each of the two screws on both projector lamps.

Panasonic_PT-D5500U_projector_Panasonic_ET-LAD55_replace_projector_lampPut the fan back in place and tighten the two screens to hold it in place. (See diagram #8)

Slide the cover a little toward the right, and secure it by tightening the screw. (See diagram #9)

NOTE: Firmly install the projector lamp unit and projector lamp cover. If not installed properly, the protection circuit will be activated and the projector will not turn back on.

To reset the projector lamp timer

Each time you switch to a new Panasonic ET-LAD55 projector lamp you need to reset the Panasonic PT-D5500U projector lamp timer.

Panasonic_PT-D5500U_projector_reset_Panasonic_ET-LAD55_projector_lamp_timer

 

  • Insert the power cord plug into the wall outlet and then press the MAIN POWER switch.
  • Press the “ I ” button on the remote control to display an image picture onto the screen.
  • Press MENU to display the MAIN MENU screen.
  • Scroll down to select OPTION2. Press ENTER to display the OPTION 2 menu.
  • Scroll down to SYSTEM INFORMATION. Press ENTER to display the SYSTEM INFORMATION menu.
  • Press and hold the ENTER button on the projector or the remote control for approximately 3 seconds. The option LAMP TIME RESET will be added to the menu.

Scroll down to select the projector that has was replaced. Select the lamp which has been changed

  • LAMP1: Replace the LAMP UNIT 1
  • LAMP2: Replace the LAMP UNIT 2
  • Press ENTER.
  • When the LAMP TIME RESET display flashes, press ENTER again.
  • The used hours of the specified lamp unit will be reset to zero.
  • Press the MENU button to leave the LAMP TIME RESET menu.

Quick reset:

  • When lamp unit 1 has been replaced: In standby mode, press the number buttons in the sequence of 737381, and then press ENTER.
  • When lamp unit 2 has been replaced: In standby mode, press the number buttons in the sequence of 737382, and then press ENTER.
  • When the projector lamps hours have been reset, the lamp monitor (LAMP1/LAMP2) will flash for 3 seconds.

Learn more tips for extending the projector lamp life in your Panasonic PT-D5500U projector.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Boxlight_CP-33T_projector_Boxlight_CP13T-930_projector_lampSwitching your old Boxlight CP-33T projector lamp for a new one by following this guide.

End of life warning messages

The Boxlight CP-33T uses the Boxlight CP13T-930 projector lamp. When this projector lamp is approaching end of life the LAMP REPLACEMENT indicator lights red. Change the Boxlight CP-33T projector lamp immediately when warning message flash on screen or it the image becomes darker or the color become unnatural.

The importance of OEM projector lamps

Your Boxlight CP-33t projector is a sophisticated machine equipped with high-end optics. In order to keep it operating at its full capacity, you need to use an OEM lamp that is properly calibrated to work with your projector. Generic lamps can be tempting due to their low prices but they can damage the optics in your projectors. These copycat lamps have also have been made with carcinogenic toxic substitutes. As a result generic lamps have shorter lives and are prone to explosions. Protect your investment and purchase an authentic projector lamp.

Find this lamp sold on Amazon by these authorized dealers:

Replacing the projector lamp

Before replacing the Boxlight CP13T-930 projector lamp follow these safety tips:

  • Disconnect the power cord on the Boxlight CP-33t projector.
  • Reduce the risk of severe burns by allowing the Boxlight CP-33t projector to cool for at least one hour. These projectors operate using high temperatures and you run the risk of severe burns if you don’t allow it to cool down.

Boxlight_CP-33T_projector_change_Boxlight_CP13T-930_projector_lamp

 

  • Turn the Boxlight CP-13t projector on its side. Loosen the screw holding the lamp cover in place.
  • Remove the two screws holding the Boxlight CP13T-930 projector lamp in place.
  • Using the wire handle on the Boxlight CP13T-930 projector lamp and gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
  • NOTE: Be sure to recycle the Boxlight CP13T-930 projector lamp as contains mercury and should not be thrown into regular garbage. Recycle it!
  • Insert the new CP13T-930 and avoid touching the actual bulb as this can result in black spots from the oil on your hands.
  • Tighten the two screws on the Boxlight CP13T-930.
  • Place the cover back onto the Boxlight CP-33t projector and tighten the lamps screw. You must now reset the lamp timer.

Boxlight_CP-33T_projector_Boxlight_CP13T-930_reset_projector_lamp_counterResetting the Boxlight CP-33T lamp counter

Once the Boxlight CP13T-930 projector lamp has been replaced, you will need to reset the lamp counter so the Boxlight CP-33t projector can accurately track the number of lamp hours remaining:

  • Turn the projector on.
  • Press the MENU button. The ON-SCREEN MENU will appear.
  • Press the POINT LEFT/RIGHT buttons to select SETTING.
  • Press the SELECT button. The SETTING MENU appears.
  • Press the POINT DOWN button and a red-arrow icon will appear.
  • Move the arrow to LAMP AGE. Press the SELECT button.
  • The message “Lamp replace monitor Reset?” is displayed.
  • Select YES to reset the Timer.

 

Extend the life of the Boxlight CP13T-930 projector lamp by reading Top tips for extending DLP projector lamp life

Interested in a green alternative?

Boxlight_CP-33t_projector_Boxlight_CP13T-930_Video_InstructionsThe Boxlight CP-33t projector has the option of also just replacing the actual bulb to re-use the plastic cage. This reduces waste and is a great way to green your projector. Watch our training video to learn more.

 

 

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_EB-X9_projector_Epson_ELPLP58_projector_lampUse this guide to replace the Epson EB-X9 projector lamp in three easy steps.

These instructions can also be used on the Epson EB-X92 projector.

Step 1: Recognizing the end of life warning signs

The Epson EB-X9 projector lamp can last for close to 4,000 hours with power consumption set to NORMAL and up to 5,000 hours if the ECO option is used. n order to maintain projector brightness and image quality, replace with a new Epson LPLP58 (V13H010L58) projector lamp as soon as possible.

When the Epson EB-X9 projector lamp is reaching end of life you’ll notice the following warning signs:

  • projector lamp indicator will flash orange and continue flashing until the projector lamp has been changed. Epson_EB-X9_projector_Epson_ELPLP58_projector_lamp_lamp_warning
  • The message Replace the lamp appears on the screen.
  • on-screen image on screen gets darker
  • colors start to  deteriorate altogether.

Check the hours left on the ELPLP58 (V13H010L58) projector lamp from the INFO Menu access off the Main Menu.

Step 2: Avoid generics, invest in authentic

When buying look for the seal of approval. Learn to spot copycat lamps posing as authentic lamps. While these generic lamps appear to be a bargain, they will actually end up costing you more money in the long run for the following rules:

Find this lamp on Amazon sold by these authorized dealers:

Step 3: Installing the new projector lamp

Before replacing the ELPLP58 (V13H010L58) projector lamp follow these important safety rules:

  1. Always unplug the power cord on the Epson EB-X9 projector before replacing the projector lamp.
  2. This projector operates using high temperature. Wait at least 60 minutes before replacing the lamp so you don’t run the risk of getting burned.
  3. Never touch the bare projector lamp bulb as the oil from your fingers will burn black marks onto the projector lamp when it heats up.
  4. Never operate the Epson EB-X9 projector with the projector lamp removed.

Epson_EB-X9_projector_Epson_ELPLP58_remove_projector_lamp_cover

 

Epson_EB-X10_projector_Epson_ELPLP58__remove_projector_lamp_screws

 

 

 

 

Remove the projector lamp cover screws and place to one side. Loosen the two screws holding the Epson ELPLP58 (V13H010L58) projector lamp in place (you can’t remove them).  Gently lift out the Epson LPLP58 projector lamp taking care not to bang it against the projector.

NOTE: The LPLP58 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

Epson_EB-X9_projector_Epson_ELPLP58_install_new_projector_lampGently insert the new Epson LPLP58 projector lamp. Make sure it fits into the Epson EB-X9 projector properly. (Check that it’s facing the right way.) Tighten the Epson LPLP58 projector lamp. You can know reset the lamp timer.

Reset the lamp timer

After you replace the lamp, you need to reset the Epson EB-X9 projector lamp timer using the projector’s menu system.

Epson_EB-X10_projector_Epson_ELPLP58_reset_projector_lamp_timer

  • Press the MENU button on the remote control or on the projector’s control panel. You see the main menu.
  • Select the RESET menu. Press ENTER.
  • Scroll down to select RESET LAMP HOURS. Press ENTER.
  • A prompt filed appears asking if you want to reset the lamp timer. Select YES. Press ENTER.
  • Press MENU to exit.

Longer life for the ELPLP58 (V13H010L58) projector lamp

Extend the life of the Epson ELPLP58 (V13H010L58) projector lamp with the following tips:

  • Set the Power Consumption to ECO option.
  • Clean the air filters regularly so the Epson EB-X9 projector doesn’t overheat.
  • Make sure there is enough airflow around the projector.
  • Turn it off when it’s not in use.
  • Learn more: Top tips for extending DLP projector lamp life.
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

BenQ_MX811ST_BenQ_5J.J3J05.001_projector_lampThis guide will help you install a new BenQ MX811ST projector lamp.

Use authentic projector lamp

It can be tempting to spend less and install a generic BenQ MX811ST projector lamp bought at a discount place. Despite their bargain prices, generic actually end of up costing ou more money in the end. Generic lamps just don’t work as well:

Keep your BenQ MX811ST projector working at its optimum level. Always use an authentic BenQ 5J.J3J05.001 projector lamp.

Find this lamp on Amazon from these authorized dealers:

When to replace the projector lamp

A flashing orange light on BenQ MX810ST projector indicates that the BenQ 5J.J3J05.001 projector lamp is reaching end of life the lamp indicator and needs to be replaced. Several warning messsages will begin to appear and you may notice the image deteriorating or the color looking off. When the final warning screen appears you must change the projector lamp immediately.

To check how many hours the projector lamp has, do the following: BenQ-_MX811ST_projector_5J.J3J05.001_projector_lamp_warning

  • Press MENU/EXIT and then press MODE/ENTER to highlight the SYSTEM SETUP: Advanced
  • Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page is displayed.
  • You will see the Equivalent Lamp Hour information appearing on the menu.
  • To leave the menu, press MENU/EXIT.
  • You can also get the lamp hour information on the INFORMATION menu.

Setting the projector to economic mode will extend the projector lamp life.

Install a new BenQ 5J.J3J05.001 projector lamp

Before changing the lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the BenQ MX811ST projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

BenQ-_MX811ST_projector_5J.J3J05_projector_lamp_remove_cover_screw

 

Loosen the screw holding the lamp cover onto the BenQ MX811ST projector.

BenQ-_MX811ST_projector_5J.J3J05_projector_lamp_remove_cover

Lift up the cover. Remove and dispose of the lamp protection film. Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

 

BenQ-_MX811ST_projector_5J.J3J05_disconnect_projector_lamp

Disconnect the projector lamp connector from the projector (Step #2 in diagram). Loosen the screw that secures the BenQ 5J.J3J05.001 projector lamp.

BenQ-_MX811ST_projector_5J.J3J05_remove_old_projector_lampSlowly and gently pull the BenQ 5J.J3J05.001 projector lamp out of the projector. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The BenQ 5J.J3J05.001 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

 

BenQ-_MX811ST_projector_5J.J3J05_install_new_projector_lampInsert the new BenQ 5J.J3J05.001 projector lamp first into the connector on the projector and reconnect the lamp connector.

BenQ-_MX811ST_projector_5J.J3J05_tighten_projector_lamp_screw

Make sure the handle is fully locked. Tighten the projector lamp screw. If the screw is too loose or too tight, the projector may not turn on.

 

BenQ-_MX811ST_projector_5J.J3J05_projector_lamp_install_coverRe-install the MX811ST lamp cover and tighten the screw.

Reset the total lamp operation timer.

 

 

Reset the projector lamp counter

BenQ-_MX811ST_projector_5J.J3J05_reset_projector_lamp_timerWhen the BenQ 5J.J3J05.001 projector lamp in the BenQ MX811ST projector has been changed the projector lamp timer must be reset:

  • Turn on the BenQ MX811ST projector.
  • After the startup logo, open the On-Screen Display (OSD) menu.
  • Go to the SYSTEM SETUP.
  • Scroll over to Advanced > Lamp Settings menu.
  • Press MODE/ENTER to display Lamp Settings page is displayed.
  • Highlight Reset lamp timer. A warning message is displayed asking if you want to reset the lamp timer.
  • Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”.

Extend the life of the BenQ 5J.J3J05.001 projector lamp last longer with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the MX761 projector lamp and set to Economic Mode to reduce the amount of power used but extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

BenQ-MX762ST_projector_5J.J3J05_projector_lamp_Video_guide

Green your BenQ MX811ST projector lamp

The BenQ MX811ST projector lamp has the option of replacing only the bulb instead of the entire BenQ 5J.J3J05.001 unit. You re-use the plastic cage and reduce waste. You can green your projector while saving money. Our instructional video shows you how step-by-step.

 

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Eiki_LC-SX4UE_projector_lamp_Eiki_610-292-4848_POA-LMP39This guide shows you how to replace the Eiki LC-SX4UE projector lamp.

Buy the right projector lamp

In order to keep your Eiki LC-SX4UE working at its best, always be sure to invest in an authentic Eiki LC-SX4UE projector lamp. It can be tricky finding an OEM lamp over the Internet. Always look for the seal of approval before buying Eiki POA-LMP39 projector lamp.

6 reasons to avoid generic lamps:

Go with original OEM projector lamps and keep your Eiki LC-SX4UE projector working!

Find this lamp sold on Amazon by these authorized dealers:

When to replace

Knowing when to replace your Eiki POA-LMP39 projector lamp and watching for end-of-life signs is your first step to keeping your projector working. The Eiki LC-SX4UE is able to detect lamp life and switch between the two. Check the number of lamps being used on the Lamp Status and started by understanding the lamp mode.

Lamp Mode Changeover: Lamp Management Function automatically changes the combination of lighting lamp (Lamp Mode) by detecting the status of each lamp. When any of the two lamps goes out, Lamp Mode is changed over from 2 lamps to 1 lamp. Lamp Mode can be switched to 2 lamps or 1 lamp manually. Check the number of lamps being used on the Lamp Status.

Lamp Status

The Eiki LC-SX4UE is equipped with two projection lamps for a brighter image. It’s recommended that you change both Eiki POA-LMP39 lamps at the same time as well as the air filter.

Eiki_SX4UE_Eiki_POA-LMP39_projector_lamp_modeThe Lamp Management Function detects the status of  lamps and displays it on screen. The lamp status is also displayed for 5 seconds when the projector is turned on. The LAMP REPLACE indicator lights yellow when either lamp is nearing end of life.

On screen status:

  • ON: Yellow lamp on screen: Lamps are functioning normally.
  • OFF: Dim Lamp: Lamp is turned off and not in use.
  • NEAR END: Red lamp: Projection Lamp is nearing its end. When image becomes darker or color becomes unnatural, replace lamp. The Lamp replace lights on the projector lights yellow at the same time.
  • OUT: X Mark on lamp: The lamp has reached its end of life and fails to turn on. It may also be defective. Replace lamp corresponding with number marked X.

Step 2:

Eiki-SX4UE_Eiki_POA-LMP39_projector_lamp_remove_coverStep 3: Replacing the Eiki POA-LMP39 projector lamp

Follow these important safety steps before replacing the Eiki POA-LMP39 projector lamp.

  • The Eiki LC-SX4UE projector operates under very high temperatures. Let it cool for one full hour before attempting to replace the lamp in order to avoid being burned.
  • Turn off the projector by pressing the power button. Wait for the light to stop flashing.
  • Turn off the power switch at the back on the projector
  • Unplug any power cords.

NOTE: To maintain quality of picture (better balance of color and brightness in entire screen), replacing both lamps at the same time.

Eiki_SX4UE_Eiki_POA-LMP39_remove_projector_lamp

Loosen the three screws on Lamp Cover and remove Lamp Cover.

 

 

 

Eiki_SX4UE_Eiki_POA-LMP39_replace_lamp

  • Loosen the 2 screws. Using the wire handle and pull out the projector lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
  • Replace the Lamp Assembly. NOTE: The Eiki POA-LMP39 projector lamp contains mercury and should be properly recycled. Don’t place it into regular garbage.
  • Make sure that Lamp Assembly is set properly. Tighten the 2 screws on the new projector lamp.
  • Replace Lamp Cover and tighten 3 screws. Connect AC Power Cord to a projector and turn projector on.
  • Reset Lamp Replacement Counter.

Reset lamp counter

Eiki_-LC-SX4UE_Eiki_POA-LMP39_reset_projector_lamp_timer

  • When the Lamp Replace Counter is reset, the LAMP REPLACE indicator stops lighting.
  • Turn projector on, press MENU button and ON-SCREEN MENU will appear.
  • Press POINT LEFT/RIGHT button(s) to move the red frame pointer to SETTING Menu icon. Press POINT DOWN button to move a red frame pointer to “Lamp counter reset.”
  • Press SELECT button.
  • Move arrow to select either Lamp 1 or Lamp 2. Press SELECT button.

Eiki_LC-SX4UE_Eiki_POA-LMP39_reset_projector_lamp_timer_2

  • Message “Lamp replace counter Reset?” is displayed.
  • Move pointer to YES and then press SELECT button.
  • NOTE: Be sure to reset correct lamp number otherwise LAMP REPLACE indicator continues lighting.
  • Another confirmation dialog box appears and select YES to reset Lamp Replace Counter.
  • Do not reset Lamp Replace Counter except after Projection lamp is replaced.

Extend the life of the Eiki POA-LMP39 projector lamp

Get more hours from your Eiki POA-LMP39 projector lamp by following these maintenance tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Eiki LC-SX4UE projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.
  • Press the MENU button to exit.

Save money, go green

Video_Changing_Lamp_for_Eiki_SX4LALooking for a green alternative? Try replacing only the bulb and re-using the same plastic cage.

Watch this how to video guide to learn more.

 

Tagged with: , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group