About Us - Page 81 of 171 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

How to replace the Epson PowerLite S1 projector lamp

Shelagh McNallyPosted on March 26, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Replacing the Epson PowerLite S1 projector lamp is easy when you follow this step-by-step guide.

Warning signs

When it’s time to replace the Epson PowerLite S1 projector lamp watch for these warning signs:

poor image quality
warning indicator flashing reds
warning light at 0.5 intervals.
lamp life is 1900 hours, the message “Replace Lamp” will appear on the bottom left corner of the screen for 30 seconds.

Finding the right lamp

Your Epson PowerLite S1 uses a Epson ELPLP 25 lamp. Look for the seal of approval to verify your Epson PowerLite S1 projector lamp is authentic and you’re buying from an authorized manufacturer.

You get what you pay for so if the price of the lamp seems like an incredible bargain, chances are it’s counterfeit. These counterfeit lamps are often advertised as “generic” and claim to be compatible with your Epson PowerLite S1. They have in fact been created using inferior parts that damage the inside of your Epson EMP-61p projector. Generic lamps also come with a health risk; since copycat manufacturers can’t get the proper materials they often using highly toxic substitutes.

Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered. Go with an authentic Epson ELPLP 25 — it’s worth the few extra dollars to save yourself problems.

Buy this lamp on Amazon from the following authorized dealers:

Step 3: Replacing the lamp

Replace the Epson PowerLite S1 projector lamp immediately when the lamp replacement indicator blinks red.

Turn the Epson PowerLite S1 projector off and allow for a 20-second cool down period. Then disconnect the power cord and allow the projector to cool for one hour before replacing the Epson ELPLP 25. Failure to do so can result in a severe burn as the Epson PowerLite S1 operates uses high heat.

Remove the Epson PowerLite S1 lamp cover by putting your fingers in the latches and lifting upwards. Put the lamp cover to one side.

Using the screwdrive that came with the Epson PowerLite S1 projector, loosen the screws holding the Epson ELPLP 25 in place.

Gently lift out the old lamp making sure not to touch the actual bulb in case it may break. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

Be sure to dispose of the used Epson ELPLP 25 lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.

Line up the new Epson ELPLP 25 lamp and lower it into the Epson PowerLite S1 projector making sure not to touch the actual bulb. Fingerprints on the bulb will turn into black spots that hampers picture quality.

Press the lamp until it clicks into place, then tighten the two fixing screws.

Replace the Epson PowerLite S1 lamp cover by first inserting the tabs, and then pressing towards the projector until it clicks into place.

You’re ready to reset the lamp timer.

Resetting the lamp timer

You’ll need to reset the lamp timer in order to ensure the Epson PowerLite S1 projector know when the Epson ELPLP 25 needs replacing. Leaving the Epson ELPLP 25 lamp in the projector before the recommended 1900 hours can result in the lamp exploding.

Use either the control panel keys on the Epson PowerLite S1 or the menu options on the remote control top access the MENU screen.

Using the arrows keys, scroll down to the RESET menu.
Click ENTER (left pointing arrow).
Scroll down to select LAMP-HOURS RESET.
Press ENTER.
Click on YES to reset the lamp hours to zero. The lamp hours will be reset.

Extending the Epson ELPLP 25 lamp life

Get more hours from your Epson ELPLP 25 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson PowerLite S1 rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.
Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP 25, Epson PowerLite S1 projector

3 Steps to a new Epson V11H128020 projector lamp

Shelagh McNallyPosted on March 26, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this 3-step guide to a Epson V11H128020 projector lamp

Poor image quality on screen can mean it’s time to replace your Epson V11H128020 projector lamp.

Step 1: Find the right lamp

Your Epson V11H128020 uses a Epson ELPLP 25 lamp. Look for the seal of approval to verify your Epson ELPLP 25 lamp is authentic and you’re buying from an authorized manufacturer.

You get what you pay for so if the price of the lamp seems like an incredible bargain, chances are it’s counterfeit. These counterfeit lamps are often advertised as “generic” and claim to be compatible with your Epson V11H128020. They have in fact been created using inferior parts that damage the inside of your Epson EMP-61p projector. Generic lamps also come with a health risk; since copycat manufacturers can’t get the proper materials they often using highly toxic substitutes.

Step 2: Know when to replace

It’s time to replace the Epson V11H128020 projector lamp when the warning indicator flashes red 0.5 intervals. When the lamp life reaches 1900 hours, the message “Replace Lamp” will appear on the bottom left corner of the screen for 30 seconds.

Step 3: Replacing the Epson ELPLP 25 lamp

Replace the Epson ELPLP 25 immediately when the lamp replacement indicator blinks red.

Turn the Epson V11H128020 projector off and allow for a 20-second cool down period. Then disconnect the power cord and allow the projector to cool for one hour before replacing the Epson ELPLP 25. Failure to do so can result in a severe burn as the Epson V11H128020 operates uses high heat.

Remove the Epson V11H128020 lamp cover by putting your fingers in the latches and lifting upwards. Put the lamp cover to one side.

Using the screwdrive that came with the Epson Epson V11H128020 projector, loosen the screws holding the Epson ELPLP 25 in place.

Gently lift out the old lamp making sure not to touch the actual bulb in case it may break. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

Be sure to dispose of the used Epson ELPLP 25 lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.

Line up the new Epson ELPLP 25 lamp and lower it into the Epson V11H128020 projector making sure not to touch the actual bulb. Fingerprints on the bulb will turn into black spots that hampers picture quality.

Press the lamp until it clicks into place, then tighten the two fixing screws.

Replace the Epson V11H128020 lamp cover by first inserting the tabs, and then pressing towards the projector until it clicks into place.

You’re ready to reset the lamp timer.

Resetting the lamp timer

You’ll need to reset the lamp timer in order to ensure the Epson V11H128020 projector know when the Epson ELPLP 25 needs replacing. Leaving the Epson ELPLP 25 lamp in the projector before the recommended 1900 hours can result in the lamp exploding.

Use either the control panel keys on the Epson V11H128020 or the menu options on the remote control top access the MENU screen.

Using the arrows keys, scroll down to the RESET menu.
Click ENTER (left pointing arrow).
Scroll down to select LAMP-HOURS RESET.
Press ENTER.
Click on YES to reset the lamp hours to zero. The lamp hours will be reset.

Extending the Epson ELPLP 25 lamp life

Get more hours from your Epson ELPLP 25 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson V11H128020 rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP 25 lamp, Epson projector lamps, Epson V11H128020 projector

Which projectors are compatible with the Epson ELPLP15 lamp?

Shelagh McNallyPosted on March 21, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Scroll down for a list of projectors that are compatible with the Epson ELPLP15 lamp.

Look for the seal of approval and buy only OEM authentic lamps. Genuine Epson ELPLP15 lamps will keep your Epson projector working at its best. Protect yourself from tricked into purchasing counterfeit “generic-compatible” lamps.

6 reasons to buy authentic and avoid generics

OEM lamps have a longer life than generics
knock off lamps are created with toxic materials and pose a health threat
authentic lamps are safer and less likely to explode
copycat lamps can damage the sensitive electronics in your projectors
generics don’t come with a guarantee or tech support. Getting a refund can be a hassle.
your warranty on the Epson will be void if you install a generic lamp.

When to replace the Epson ELPLP15 lamp

When it’s approaching end of life there will be some very distinct signs that the Epson ELPLP15 needs a new lamp. Watch for the following telltale signs:

Dark image
Image that has deteriorated
“Replace the Lamp” warning message appears on screen
Lamp light flashes orange or red

Compatible projectors with the Epson ELPLP15 lamp

The Epson ELPLP15 lamp can be used with the following projectors:

Epson EMP-600 Epson EMP-600P Epson EMP-800 Epson EMP-800P Epson EMP-800UG Epson EMP-810 Epson EMP-810P Epson EMP-810UG Epson EMP-811 Epson EMP-811P Epson EMP-820 Epson EMP-820P Epson PowerLite 600P Epson Powerlite 800P Epson Powerlite 810P Epson PowerLite 811P Epson PowerLite 820P

For step-by-step instructions on replacing your Epson ELPLP15 lamp, click on your projector listed below:

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson PowerLite 600P projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson Powerlite 800P projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson Powerlite 810P projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson EMP-811P projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson PowerLite 820P projector.

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Blocked air filters can cause your projector to overheat and shorten the lamp life.
Turning off the Epson projector for at least one hour per day and limiting use to 5 hours of daily usage will prolong lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. The projector overheating can shorten the lamp life.
Learn more with Top tips for extending DLP projector lamp life

Save

Tagged with: Epson ELPLP15 lamp, Epson EMP-600, Epson EMP-600P, Epson EMP-800, Epson EMP-800P, Epson EMP-800UG, Epson EMP-810, Epson EMP-810P, Epson EMP-810UG, Epson EMP-811, Epson EMP-811P, Epson EMP-820, Epson EMP-820P, Epson PowerLite 600P, Epson Powerlite 800P, Epson Powerlite 810P, Epson PowerLite 811P, Epson PowerLite 820P, how to replace Epson projector lamps

How to install an Epson EMP-TW10 projector lamp

Shelagh McNallyPosted on March 21, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this handy guide to replace the Epson EMP-TW10 projector lamp

You can expect up to 1900 hours of Epson EMP-TW10 projector lamp before it reaches end of life and needs to be replaced.

Warning signs

Poor image quality on your Epson EMP-TW10 projector is one the warning signs that the needs replacing.

It’s time to replace the Epson EMP-TW10 projector lamp when the warning indicator flashes red at 0.5 intervals. The message “Replace Lamp” will appear on the bottom left corner of the screen for 30 seconds.

Authentic vs. generic

Look for the seal of approval when you are buying your Epson EMP-TW10 projector lamp. You’ll need the Epson ELPLP 25 model. While generic have a lower pricetag, there are plenty of downsides to these lamps. Protect your health, the health of your Epson EMP-TW10 projector and buy authentic. Don’t be fooled by the generic manufacturers: Learn the 7 Ways to Spot a Counterfeit Lamp.

Six reasons to avoid generics:

prone to explosions because of their inferior workmanship
don’t last the full 1400 hours
health hazard due to the toxic materials used
not calibrated properly and will damage the optics
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-TW10 projector will become void.

Buy this lamp on Amazon from the following authorized dealers:

Replacing the Epson EMP-TW10 projector lamp

Replace the Epson EMP-TW10 projector lamp immediately when the lamp replacement indicator blinks red.

Turn the Epson EMP-TW10 projector off and allow for a 20-second cool down period. Then disconnect the power cord and allow the projector to cool to the touch before replacing the Epson ELPLP 25. These projectors operate under high heat and there is the potential for a serious burn if the projector has not cooled down long enough.

Remove the Epson EMP-Tw10 lamp cover by putting your fingers in the latches and lifting upwards. Put the lamp cover to one side.

Using the screwdrive that came with the Epson EMP-TW10 projector, loosen the screws holding the Epson ELPLP 25 in place.

Gently light up the old lamp making sure not to touch the actual bulb in case it may break. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

Be sure to dispose of the used Epson ELPLP 25 lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.

Avoiding touching the actual glass bulb while lining up the new Epson ELPLP 25 lamp. Fingerprints on the bulb will turn into black spots that hampers picture quality.

Slowly lower the new lamp into the Epson EMP-TW10 projector making sure not to touch the actual bulb. Press the Epson ELPLP 25 lamp until it clicks into place, then tighten the two fixing screws.

Replace the Epson EMP-TW10 lamp cover by first inserting the tabs, and then pressing towards the projector until it clicks into place.

You’re ready to reset the lamp timer.

Resetting the lamp timer

You’ll need to reset the lamp timer in order to ensure the Epson EMP-TW10 projector know when the Epson ELPLP 25 needs replacing. Leaving the Epson ELPLP 25 lamp in the projector before the recommended 1900 hours can result in the lamp exploding.

Use either the control panel keys on the Epson EMP-TW10 or the menu options on the remote control top access the MENU screen.

Using the arrows keys, scroll down to the RESET menu.
Click ENTER (left pointing arrow).
Scroll down to select LAMP-HOURS RESET.
Press ENTER to open the Lamp-Hours Reset screen.
Click on YES to reset the lamp hours to zero. Press ENTER.
The lamp hours will be reset. The hours will be displayed as 0H until 10 hours of lamp usage has been reached.

Extending life of the Epson ELPLP 25 lamp

Get more hours from your Epson ELPLP 25 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson EMP-TW10 rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP 25 lamp, Epson EMP-TW10, Epson projector lamps

Instructions for replacing the Epson EMP-S1 projector lamp

Shelagh McNallyPosted on March 20, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this guide to replace the Epson EMP-S1 projector lamp

Poor image quality on your Epson EMP-S1 projector? ? It may be time to replace the Epson EMP-S1 projector lamp.

It’s time to replace the lamp when the Warning indicator flashes red 0.5 intervals. When the lamp life reaches 1900 hours, the message “Replace Lamp” will appear on the bottom left corner of the screen for 30 seconds.

Installing the right lamp

It’s crucial to install the proper type of Epson ELPLP 25 lamp. Avoid buying generic knock-offs or lamps advertised as “compatible.” Go with an authentic Epson ELPLP 25 OEM lamp sold by a dependable seller. Using a counterfeit generic lamp may result in poor illumination as well as malfunction of the sensitive components in your projector.

Counterfeit lamps are prone to explosion and have been created using toxic substances such as Krypton-85. Installing a generic lamp will also void any warranty for your Epson EMP-S1 projector. Learn the 7 Ways to spot a counterfeit lamp.

Buy this lamp on Amazon from the following authorized dealers:

Replacing the Epson ELPLP 25 lamp

Replace the Epson ELPLP 25 immediately when the lamp replacement indicator blinks red.

Turn the Epson EMP-S1 projector off and allow for a 20-second cool down period. Then disconnect the power cord and allow the projector to cool for one hour before replacing the Epson ELPLP 25. Failure to do so can result in a severe burn as the Epson EMP-S1 operates uses high heat.

Remove the Epson EMP-S1 lamp cover by putting your fingers in the latches and lifting upwards. Put the lamp cover to one side.

Using the screwdrive that came with the Epson EMP-S1 projector, loosen the screws holding the Epson ELPLP 25 in place.

Gently lift out the old lamp making sure not to touch the actual bulb in case it may break. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

Be sure to dispose of the used Epson ELPLP 25 lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.

Line up the new Epson ELPLP 25 lamp and lower it into the Epson EMP-S1 projector making sure not to touch the actual bulb. Fingerprints on the bulb will turn into black spots that hampers picture quality.

Press the lamp until it clicks into place, then tighten the two fixing screws.

Replace the Epson EMP-S1 lamp cover by first inserting the tabs, and then pressing towards the projector until it clicks into place.

You’re ready to reset the lamp timer.

Resetting the lamp timer

You’ll need to reset the lamp timer in order to ensure the Epson EMP-S1 projector know when the Epson ELPLP 25 needs replacing. Leaving the Epson ELPLP 25 lamp in the projector before the recommended 1900 hours can result in the lamp exploding.

Use either the control panel keys on the Epson EMP-S1 or the menu options on the remote control top access the MENU screen.

Using the arrows keys, scroll down to the RESET menu.
Click ENTER (left pointing arrow).
Scroll down to select LAMP-HOURS RESET.
Press ENTER.

Click on YES to reset the lamp hours to zero. The lamp hours will be reset.

Extending the Epson ELPLP 25 lamp life

Get more hours from your Epson ELPLP 25 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson EMP-S1 rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP 25 lamp, Epson EMP-S1 projector, Epson projector lamps

Matching projectors with the Epson ELPLP15 lamp

Shelagh McNallyPosted on March 19, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Which projectors work best with Epson ELPLP15 lamp

Keep your Epson projector working at its best and prolong its life by installing an authentic Epson ELPLP15 lamp. Only projector lamps created by an authentic manufacturer. Look for the seal of approval and buy only OEM authentic lamps. You’ll be getting a far superior product with a replacement guarantee and tech support. Scroll down for a list of projectors that are compatible with the Epson ELPLP15.

6 reasons to buy authentic and avoid generics

OEM lamps have a longer life than generics
knock off lamps are created with toxic materials and pose a health threat
authentic lamps are safer and less likely to explode
copycat lamps can damage the sensitive electronics in your projectors
generics don’t come with a guarantee or tech support. Getting a refund can be a hassle.
your warranty on the Epson will be void if you install a generic lamp.

Protect yourself from tricked into purchasing counterfeit “generic-compatible” lamps.

When to replace the Epson ELPLP15 lamp

When it’s approaching end of life there will be some very distinct signs that the Epson ELPLP15 needs a new lamp. Watch for the following telltale signs:

Dark image
Image that has deteriorated
“Replace the Lamp” warning message appears on screen
Lamp light flashes orange or red

Compatible projectors with the Epson ELPLP15 lamp

The Epson ELPLP15 lamp can be used with the following projectors:

For step-by-step instructions on replacing your Epson ELPLP15 lamp, click on your projector listed below:

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson EMP-810P projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson EMP-810UG projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson EMP-811 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson EMP-811P projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson EMP-820 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP15 projector lamp for the Epson EMP-820P projector.

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Blocked air filters can cause your projector to overheat and shorten the lamp life.
Turning off the Epson projector for at least one hour per day and limiting use to 5 hours of daily usage will prolong lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. The projector overheating can shorten the lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: Epson ELPLP15, Epson EMP-600, Epson EMP-600P, Epson EMP-800, Epson EMP-800P, Epson EMP-800UG, Epson EMP-810, Epson EMP-810P, Epson EMP-810UG, Epson EMP-811, Epson EMP-811P, Epson EMP-820, Epson EMP-820P, Epson PowerLite 600P, Epson Powerlite 800P, Epson Powerlite 810P, Epson PowerLite 811P, Epson PowerLite 820P, Epson projector lamps

How to replace the Epson PowerLite 821p projector lamp

Shelagh McNallyPosted on March 18, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

How to replace the Epson EMP-821p projector lamp

When it’s time to replace the Epson PowerLite 821p projector lamp follow this guide.

Be ready with the correct lamp

You’ll want to keep your Epson PowerLite 821p working at its best levels. Genuine OEM Epson ELPLP30 lamps are properly calibrated to work with the highly sophisticated optics in your projector. Using a proper Epson ELPLP30 in your Epson PowerLite 821p will guarantee a longer life for the projector.

Generic lamps may appear like an incredible bargain due to their price tag. But when you factor in all the problems they cause, generic lamps actually cost more in the long run. Here’s a list of their associated problems:

prone to explosions because of their inferior workmanship
don’t last the full 3000 hours
health hazard due to the toxic materials used
not calibrated properly and will damage the optics
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson PowerLite 821p projector will become void.

Protect your health and keep your Epson PowerLite 821p working at optimal levels. Do you Learn the know how to spot a counterfeit lamp?

When to replace the Epson ELPLP30

You can expect between 2000 to 3000 hours of Epson ELPLP30 lamp life with your Epson PowerLite 821p. If the Epson PowerLite 821p projector’s Brightness Mode is set to low, you can expect up to 3000 hours. If the Epson PowerLite 821p projector’s Brightness Mode is set to high the lamp will last up to 2000 hours. The replacement warnings will be triggered at 2000 hours.

Warning signs

Watch for the warning signs that the Epson ELPLP30 is approaching end of life and needs to be replaced:

the message “Replace the Lamp” appears on screen when the projector is turned on.
the lamp light on the Epson PowerLite 821p begins to flashing orange red.
the picture gets darker and continues to deteriorate

When you see any of these signs, get prepared to change the Epson ELPLP30 lamp.

Step 3: Installing the Epson ELPLP30

You’ll need to these preparatory steps before installing the new Epson ELPLP30 in the Epson PowerLite 821p projector:

press the off power button twice to power down the projector.
after you hear two beeps, unplug the power cord.
give the projector one full hour to cool. The Epson PowerLite 821p operates on high heat and you will burn yourself if the projector has not cooled down.

Using the screwdriver provided, loosen the screw holding the Epson PowerLite 821p lamp cover in place.

Once the lamp cover screw has been loosened, slide the cover off the Epson PowerLite 821p projector. Place it to one side of safe keeping.

Using the screw driver provided, loosen both screws holding the Epson ELPLP30 screws in place. They will not come out of the lamp altogether.

Grab the handle on the Epson ELPLP30 and gently pull the lamp up. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

NOTE: Make sure to properly recycle the Epson ELPLP30 lamp. It can’t be thrown into regular garbage since it contains mercury. Your authorized manufacturer will recycle the lamp for you at no extra cost.

Remove the packaging from the new Epson ELPLP30 lamp being sure not to touch the glass bulb. Your fingerprints can leave oil marks on the glass causing black spots to appear on screen when the projector heats up.

Line up the Epson ELPLP30 lamp and gently lower it into the PowerLite 821p projector.

Line up the lamp cover and slide it back onto the projector. Tighten the screw on the lamp cover. You’re now ready to reset the lamp operating timer.

Resetting the Lamp Operating Timer

The Lamp Operating Timer determines when the Epson ELPLP30 lamp is reaching its 2000 hours end of life. Only reset this option when you have installed a new lamp otherwise you run the risk of using an older lamp past its recommended usage. This can cause the old lamp to explode.

To reset the Lamp Operating Timer:

Plug the power cord back into the projector
Press the on button and wait for the projector to warm up.
Press the MENU button to display the Menu options.
Scroll down to select RESET menu. Press enter.
Scroll down and choose RESET LAMP HOURS option
Press ENTER.
The reset lamp hour message will show up.

Select YES
Press ENTER.
Lamp hours will be set to zero.

Extending the Epson ELPLP30 lamp life

Get more hours from your Epson ELPLP30 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson PowerLite 821p rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Set brightness to low and get another 1000
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP30, Epson projector lamps

Replace the Epson Powerlite 81p projector lamp

Shelagh McNallyPosted on March 15, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — 6 Comments ↓

Our quick guide shows how to replace the Epson Powerlite 81p projector lamp

Learn where to find the right Epson Powerlite 81p projector lamp and how to install it

Note: These instructions can also be used for the Epson Powerlite 81 projector.

You can expect between 2000 to 3000 hours of Epson ELPLP30 lamp life used in the Epson PowerLite 81p If the Epson PowerLite 81p projector’s Brightness Mode is set to low, you can expect up to 3000 hours. The replacement warnings will be triggered at 2000 hours.

Warning signs

As the Epson ELPLP30 approaches its end of life, some telltale signs will start showing up:

Replace the Lamp” message appears on screen when the projector is turned on.
the lamp light on the Epson PowerLite 81p begins flashing orange.
the picture gets darker and continues to deteriorate
When you see any of these signs, get prepared to change the Epson ELPLP30 lamp.

Why buy authentic

Authentic lamps are the only option if you want to keep your Epson PowerLite 81p working at its optimum levels. There are plenty of generics out there that can damage the inside of your Epson Powerlite 81p. If the price of the Epson ELPLP30 lamps seems really low, the you are about to buy is a counterfeit. Often advertised as “generic,” these lamps and claim to be compatible with your Epson EMP-81p. They have in fact been created using inferior parts that are a health risk due to xic substitutes.

Replace the Epson ELPLP30 lamp with a guaranteed authentic lamp. Look for the seal of approval to verify your Epson ELPLP30 lamp is authentic and buy from an authorized manufacturer.

Installing the Epson ELPLP30

You’ll need to these preparatory steps before installing the new Epson ELPLP30 in the Epson PowerLite 81p projector:

press the off power button twice to power down the projector and after you hear two beeps followed by 60 seconds of no sound,
give the projector one full hour to cool. The Epson PowerLite 81p operates on high heat and you will burn yourself if the projector has not cooled down.

Using the screwdriver provided, loosen the screw holding the Epson PowerLite 81p lamp cover in place.

Once the lamp cover screw has been loosened, slide the cover off the Epson PowerLite-81p projector. Place it to one side of safe keeping.

Using the screw driver provided, loosen both screws holding the Epson ELPLP30 screws in place. They will not come out of the lamp altogether.

Grab the handle on the Epson ELPLP30 and gently pull the lamp up. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

Line up the Epson ELPLP30 lamp and gently lower it into the EMP-81p projector.

Line up the lamp cover and slide it back onto the projector. Tighten the screw on the lamp cover. You’re now ready to reset the lamp operating timer.

Resetting the Lamp Operating Timer

To reset the Lamp Operating Timer:

Plug the power cord back into the projector
Press the on button and wait for the projector to warm up.
Press the MENU button to display the Menu options.
Scroll down to select RESET menu. Press enter.
Scroll down and choose RESET LAMP HOURS option
Press ENTER.
The reset lamp hour message will show up.

Select YES
Press ENTER.
Lamp hours will be set to zero.

Extending the Epson ELPLP30 lamp life

Get more hours from your Epson ELPLP30 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson PoewerLite-81p rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Set brightness to low and get another 1000
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP30, Epson Powerlite 81, Epson Powerlite 81p projector

3 Steps to a new Epson PowerLite 61p projector lamp

Shelagh McNallyPosted on March 15, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow our step-by-step guide to replace the Epson PowerLite 61p projector lamp

The Epson PowerLite 61p projector lamp can be replaced in 3 quick steps.

Note: These instructions can also be used for the Epson Powerlite 61 projector.

Step 1: Buy authentic lamps

Your Epson PowerLite 61p uses a Epson ELPLP30 lamp. Look for the seal of approval to verify your Epson ELPLP30 lamp is authentic and you’re buying from an authorized manufacturer.

You get what you pay for so if the price of the lamp seems like an incredible bargain, chances are it’s counterfeit. These counterfeit lamps are often advertised as “generic” and claim to be compatible with your Epson PowerLite-61p. They have in fact been created using inferior parts that damage the inside of your Epson EMP-61p projector. Generic lamps also come with a health risk; since copycat manufacturers can’t get the proper materials they often using highly toxic substitutes.

Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered. Go with an authentic Epson ELPLP30 — it’s worth the few extra dollars to save yourself problems.

Step 2: Know when to replace

The Epson PowerLite-61p projector lamp life will vary according to how much the projector is used. If the Epson PowerLite-61p projector’s Brightness Mode is set to low, you can expect up to 3000 hours. If the Epson PowerLite-61p projector’s Brightness Mode is set to high the lamp will last up to 2000 hours. The replacement warnings will be triggered at 2000 hours.

Warning signs

Watch for the warning signs that the Epson ELPLP30 is approaching end of life and needs to be replaced:

the lamp light on the Epson PowerLite-61p begins to flashing orange red.
the picture gets darker and continues to deteriorate
the message “Replace the Lamp” appears on screen when the projector is turned on.

When you see any of these signs, get prepared to change the Epson ELPLP30 lamp.

Step 3: Installing the Epson PowerLite-61p projector lamp

Before opening up the Epson EMP-61p to install the Epson ELPLP30 lamp, follow these steps:

press the off power button twice to power down the projector.
after you hear two beeps, unplug the power cord.
give the projector one full hour to cool. The Epson PowerLite 61p operates on high heat and you will burn yourself if the projector has not cooled down.

Using the screwdriver provided, loosen the screw holding the Epson PowerLite 61p lamp cover in place.

Once the lamp cover screw has been loosened, slide the cover off the Epson PowerLite-61p projector. Place it to one side of safe keeping.

Using the screw driver provided, loosen both screws holding the Epson ELPLP30 screws in place. They will not come out of the lamp altogether.

Grab the handle on the Epson ELPLP30 and gently pull the lamp up. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP30 should not be thrown into regular garbage! Since it contains mercury and should be properly recycled!

Line up the Epson ELPLP30 lamp and gently lower it into the Epson PowerLite-61p projector.

Line up the lamp cover and slide it back onto the projector. Tighten the screw on the lamp cover. You’re now ready to reset the lamp operating timer.

Resetting the Lamp Operating Timer

To reset the Lamp Operating Timer:

Plug the power cord back into the projector
Press the on button and wait for the projector to warm up.
Press the MENU button to display the Menu options.
Scroll down to select RESET menu. Press enter.
Scroll down and choose RESET LAMP HOURS option
Press ENTER.
The reset lamp hour message will show up.

Select YES
Press ENTER.
Lamp hours will be set to zero.

Extending the Epson ELPLP30 lamp life

Get more hours from your Epson ELPLP30 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson PowerLite-61p rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP30 lamp, Epson PowerLite 61p projector, Epson projector lamps

3 Steps to a new Epson EMP-821p projector lamp

Shelagh McNallyPosted on March 12, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

This guide shows how to replace the Epson EMP-821p projector lamp

Replacing the Epson EMP-821p projector lamp is as easy as 1-2-3 when you follow our quick guide.

Note: The instructions can also be used for the Epson EMP-821 projector.

Step 1: Have the correct lamp ready

Your Epson EMP-821p has been built to operate with a genuine OEM manufactured lamp properly calibrated to work with the highly sophisticated optics in the projector. A true Epson ELPLP30 lamps has been manufactured to meet the needs of the Epson EMP-821p will guarantee a longer life for the projector.

Why avoid generic lamps?

prone to explosions because of their inferior workmanship
don’t last the full 3000 hours
health hazard due to the toxic materials used
not calibrated properly and will damage the optics
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-821p projector will become void.

Protect your health and keep your Epson EMP-821p working at optimal levels. Do you Learn the know how to spot a counterfeit lamp?

Step 2: Knowing when to replace

You can expect between 2000 to 3000 hours of Epson ELPLP30 lamp life with your Epson EMP-821p. If the Epson EMP-821p projector’s Brightness Mode is set to low, you can expect up to 3000 hours. If the Epson EMP-821p projector’s Brightness Mode is set to high the lamp will last up to 2000 hours. The replacement warnings will be triggered at 2000 hours.

Warning signs

Watch for the warning signs that the Epson ELPLP30 is approaching end of life and needs to be replaced:

the message “Replace the Lamp” appears on screen when the projector is turned on.
the lamp light on the Epson EMP-821p begins to flashing orange red.
the picture gets darker and continues to deteriorate

When you see any of these signs, get prepared to change the Epson ELPLP30 lamp.

Step 3: Installing the Epson ELPLP30

You’ll need to these preparatory steps before installing the new Epson ELPLP30 in the Epson EMP-821p projector:

press the off power button twice to power down the projector.
after you hear two beeps, unplug the power cord.
give the projector one full hour to cool. The Epson EMP-821p operates on high heat and you will burn yourself if the projector has not cooled down.

Using the screwdriver provided, loosen the screw holding the Epson EMP-821p lamp cover in place.

Once the lamp cover screw has been loosened, slide the cover off the Epson EMP-821p projector. Place it to one side of safe keeping.

Using the screw driver provided, loosen both screws holding the Epson ELPLP30 screws in place. They will not come out of the lamp altogether.

Grab the handle on the Epson ELPLP30 and gently pull the lamp up. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

Line up the Epson ELPLP30 lamp and gently lower it into the EMP-821p projector.

Line up the lamp cover and slide it back onto the projector. Tighten the screw on the lamp cover. You’re now ready to reset the lamp operating timer.

Resetting the Lamp Operating Timer

To reset the Lamp Operating Timer:

Plug the power cord back into the projector
Press the on button and wait for the projector to warm up.
Press the MENU button to display the Menu options.
Scroll down to select RESET menu. Press enter.
Scroll down and choose RESET LAMP HOURS option
Press ENTER.
The reset lamp hour message will show up.

Select YES
Press ENTER.
Lamp hours will be set to zero.

Extending the Epson ELPLP30 lamp life

Get more hours from your Epson ELPLP30 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson EMP-821p rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Set brightness to low and get another 1000
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP30 lamp, Epson EMP-821 projector, Epson projector lamps