About Us - Page 96 of 171 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

How to replace the Epson PowerLite Home Cinema 8350 projector lamp

Shelagh McNallyPosted on November 28, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — 5 Comments ↓

Here is your D.I.Y. guide to installing a new Epson PowerLite Home Cinema 8350 projector lamp

When it’s time to replace the Epson PowerLite Home Cinema 8350 projector lamp you’ll see the following warning signs:

The projector image gets darker and starts to deteriorate.
The projector lamp flashes red.
The warning message REPLACE THE LAMP appears on screen.

Buy authentic

Your Epson Home Cinema 8350 projector is a sophisticated machine with sensitive electronic components.

You’ll want to install an authentic Epson ELPLP49 lamp to keep your Epson PowerLite Home Cinema 8350 projector working properly and to get the best picture quality. Although cheaper at first, generic knock-off lamps are actually not that great a bargain. These so-called “compatible” lamps are prone to explosion, have poor illumination, a shorter lamp life and can cause permanent damaged to the sensitive electronic components in your Epson PowerLite Home Cinema 8350 projector.

6 reasons to avoid generics

generics have a shorter lamp life than original lamps
compatible are created with toxic materials and carcinogenic parts including Krypton-85
knock off lamps are prone to explosions
generic lamps damage the sensitive electronics in your projectors
when you buy copy-cat lamps you get no guarantee or refunds
installing a generic lamp voids your projector’s warranty.

Learn the 7 Ways to spot a counterfeit lamp.

Find this authentic lamp on Amazon sold by these authorized dealers:

Install a new Epson PowerLite Home Cinema 8350 projector lamp

Before installation:

Turn power button off wait for light to stop flashing
Turn off power swtich on the back of the Epson PowerLite Home Cinema 8350 projector
Unplug the power cord
Allow the Epson PowerLite Home Cinema 8350 to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The cover for the Epson PowerLite Home Cinema 8350 projector lamp is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the lamp cover.

2. Remove the two screws on either side of Epson ELPLP49 lamp. Place the screws to either side.

3. Pull the lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4. Take the new Epson ELPLP49 lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

5. Replace the Epson ELPLP49 screws on the newly installed lamp.

6. Re-connect the lamp cover. Tighten the screws on the cord and turn on the Epson PowerLite Home Cinema 8350 projector.

7. Re-attach the power cord. Turn the projector on and let it warm up.

8. Reset the Lamp Operating time.

Reset the 8350 projector lamp timer

Reset the Epson PowerLite Home Cinema 8350 Lamp Replacement Counter only when the Epson ELPLP49 lamp has been replaced.

Turn the Epson PowerLite Home Cinema 8350 projector on.
Press MENU to display the configuration menu.
Press the down arrow to move down the menu to the Reset option.

Press Enter to enter the Reset Menu.
Press the down arrow to move down the menu to the Reset Lamp Hours option.
Press Enter.

When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
Use the cursor to move to the YES option.
Press Enter to reset the lamp hours to zero.

Prolong the life of the Epson ELPLP49 lamp:

Extend the life of the newly installed Epson ELPLP49 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite Home Cinema 8350 and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

3 Steps to a new Epson PowerLite Home Cinema 6500 UB projector lamp

Shelagh McNallyPosted on November 28, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Changing the projector lamp in your Epson PowerLite Home Cinema 6500 UB projector is as easy as 1-2-3!

Follow our 3-step guide for quick and easy replacement of the Epson ELPLP49 projector lamp. It will take less than 10 minutes to get your Epson PowerLite Home Cinema 6500 UB back up and running with its new projector .

NOTE: These instructions can also be used for the Ensemble HD Home Cinema 6500.

Step 1: Know when to replace

Watch for the signs that it’s time to replace the Epson ELPLP49 projector lamp:

The projector image gets darker and starts to deteriorate.
The projector lamp flashes red.
The warning message REPLACE THE LAMP appears on screen.

A replacement warning message will also appear on screen. You can expect 3900 hours of lamp life depending on the settings and usage.

Step 2: Buy the right projector lamp

You’ll want to install an authentic Epson ELPLP49 lamp to keep your PowerLite Home Cinema 6500 UB projector working properly and to get the best picture quality. Although cheaper at first, generic knock-off lamps are actually not that great a bargain. Go with an authentic projector lamp to keep your projector working at its best.

6 reasons to avoid generics

shorter lamp life than original lamps
created with toxic materials and carcinogenic parts including Krypton-85
prone to explosions
damage the sensitive electronics in your projectors
no safeguards to protect your eyesight
installing a generic lamp voids your projector’s warranty.

Learn the 7 Ways to spot a counterfeit lamp.

Find this authentic lamp on Amazon sold by these authorized dealers:

Step 3: Install a new Epson ELPLP49 projector lamp

Before installation:

Turn power button off wait for light to stop flashing
Turn off power switch on the back of the Epson PowerLite Home Cinema 6500 UB projector
Unplug the power cord
Allow the Epson PowerLite Home Cinema 6500 UB to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover for the Epson PowerLite Home Cinema 6500 UB is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the projector lamp cover.

2. Remove the two screws on either side of Epson ELPLP49 projector lamp. Place the screws to either side.

3. Pull the projector lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4, Take the new Epson ELPLP49 lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

5. Replace the Epson ELPLP49 screws on the newly installed projector lamp.

6. Re-connect the projector lamp cover. Tighten the screws on the cord and turn on the Epson PowerLite Home Cinema 6500 UB projector.

Reset the Lamp Operating time.

Reset the Epson Lamp Timer

Reset the Epson PowerLite Home Cinema 6500 UB Lamp Replacement Counter only when the Epson ELPLP49 lamp has been replaced.

Turn the Epson PowerLite Home Cinema 6500 UB
projector on.
Press MENU to display the configuration menu.
Press the down arrow to move down the menu to the Reset option.

Press Enter to enter the Reset Menu.
Press the down arrow to move down the menu to the Reset Lamp Hours option.
Press Enter.

When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
Use the cursor to move to the YES option.
Press Enter to reset the lamp hours to zero.

Prolong the life of the Epson ELPLP49 lamp:

Extend the life of the newly installed Epson ELPLP49 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite Home Cinema 6500 UB and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: Epson ELPLP49 projector lamp, Epson PowerLite Home Cinema 6500 UB projector, Epson projector lamps, replacement projector lamps

Your guide to a new Epson PowerLite Home Cinema 6100 projector lamp

Shelagh McNallyPosted on November 28, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — 8 Comments ↓

When it’s time to replace the Epson PowerLite Home Cinema 6100 projector lamp, follow our guide

Note: These instructions can also be used for the Ensemble HD Home Cinema 6100 projector

Watch for the signs that it’s time to replace the Epson ELPLP49 projector lamp:

The projector image gets darker and starts to deteriorate.
The projector lamp flashes red.
The warning message REPLACE THE LAMP appears on screen.

You can expect 4000 hours from the projector lamp depending on the settings and usage.

Buy authentic

Your Epson PowerLite Home Cinema 6100 is a sophisticated machine with sensitive electronic components. The Epson ELPLP49 projector lamp has been designed specifically to keep your projector operating at optimum levels. You can expect up to 4000 hours when you install an authentic Epson ELPLP49 depending on usage and how often you maintain your projector.

You’ll want to install an authentic Epson ELPLP49 lamp to keep your PowerLite Home Cinema 6100 projector working properly and to get the best picture quality. Although cheaper at first, generic knock-off lamps are actually not that great a bargain. These so-called “compatible” are simply not worth the hassles they cause with your Epson PowerLite Home Cinema 6100 projector.

Find this authentic lamp on Amazon sold by these authorized dealers:

6 reasons to avoid generics

generics have a shorter lamp life than original lamps
compatible are created with toxic materials and carcinogenic parts including Krypton-85
knock off lamps are prone to explosions
generic lamps damage the sensitive electronics in your projectors
when you buy copy-cat lamps you get no guarantee or refunds
installing a generic lamp voids your projector’s warranty.

Learn the 7 Ways to spot a counterfeit lamp.

Install a new Epson ELPLP49 lamp

Before installation:

Turn power button off wait for light to stop flashing
Turn off power swtich on the back of the Epson PowerLite Home Cinema 6100 projector
Unplug the power cord
Allow the Epson PowerLite Home Cinema 6100 to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover for the Epson PowerLite Home Cinema 6100 is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the projector lamp cover.

2. Remove the two screws on either side of Epson ELPLP49 projector lamp. Place the screws to either side.

3. Pull the lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4. Take the new Epson ELPLP49 projector lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

5. Replace the Epson ELPLP49 screws on the newly installed projector lamp.

6. Re-connect the prrojector lamp cover. Tighten the screws on the cord and turn on the Epson PowerLite Home Cinema 6100 projector.

You are now ready to reset the Lamp Operating Time function.

Step 3: Reset the Epson Lamp Timer

Reset the Epson PowerLite Home Cinema 6100 Lamp Replacement Counter only when the Epson ELPLP49 projector lamp has been replaced.

Turn the Epson PowerLite Home Cinema 6100 projector on.
Press MENU to display the configuration menu.
Press the down arrow to move down the menu to the Reset option.

Press Enter to enter the Reset Menu.
Press the down arrow to move down the menu to the Reset Lamp Hours option.
Press Enter.

When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
Use the cursor to move to the YES option.
Press Enter to reset the lamp hours to zero.

Prolong the life of the Epson ELPLP49 lamp

Extend the life of the newly installed Epson ELPLP49 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite Home Cinema 6100 and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic projector lamps, Epson ELPLP49 projector lamp, Epson PowerLite Home Cinema 6100 projector, Epson projector lamps, replacement projector lamps

DIY guide to a new Epson EH-TW5800 projector lamp

Shelagh McNallyPosted on November 28, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — 6 Comments ↓

Your D.I.Y. guide to installing a new Epson EH-TW5800 projector lamp

When it’s time to replace the Epson EH-TW5800 projector lamp you’ll see the orange warning light blinking.

A replacement warning message will also appear on screen. You can expect 3900 hours of lamp from the lamp depending on the settings and usage.

Buy authentic

Your Epson EH-TW5800 is a sophisticated machine with sensitive electronic components. The Epson ELPLP49 projector lamp has been designed specifically to keep your projector operating at optimum levels.

You’ll want to install an authentic Epson ELPLP49 lamp to keep your Epson EH-TW5800 projector working properly and to get the best picture quality. Although cheaper at first, generic knock-off lamps are actually not that great a bargain. These so-called “compatible” lamps are prone to explosion, have poor illumination, a shorter lamp life and can cause permanent damaged to the sensitive electronic components in your Epson EH-TW5800 projector.

ind this authentic lamp on Amazon sold by these authorized dealers:

6 reasons to avoid generics

generics have a shorter lamp life than original lamps
compatible are created with toxic materials and carcinogenic parts including Krypton-85
knock off lamps are prone to explosions
generic lamps damage the sensitive electronics in your projectors
when you buy copy-cat lamps you get no guarantee or refunds
installing a generic lamp voids your projector’s warranty.

Learn the 7 Ways to spot a counterfeit lamp.

Install a new Epson ELPLP49 lamp

Before installation:

Turn off the projector and unplug the AC cord.
Allow the Epson EH-TW5800 to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover for the Epson EH-TW5800 is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the lamp cover.

2. Remove the two screws on either side of Epson ELPLP49 lamp. Place the screws to either side.

3. Pull the lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4. Take the new Epson ELPLP49 lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

5. Replace the Epson ELPLP49 screws on the newly installed lamp.

6. Re-connect the lamp cover. Tighten the screws on the cord and turn on the Epson EH-TW5800 projector.

7. Re-attach the power cord. Turn the projector on and let it warm up.

8. Reset the Lamp Operating time.

Reset the Epson EH-TW5800 Lamp Timer

Reset the Epson EH-TW5800 Lamp Replacement Counter only when the Epson ELPLP49 lamp has been replaced.

Turn the Epson EH-TW5800 projector on.
Press MENU to display the configuration menu.
Press the down arrow to move down the menu to the Reset option.

Press Enter to enter the Reset Menu.
Press the down arrow to move down the menu to the Reset Lamp Hours option.
Press Enter.

When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
Use the cursor to move to the YES option.
Press Enter to reset the lamp hours to zero.

Prolong the life of the Epson ELPLP49 lamp:

Extend the life of the newly installed Epson ELPLP49 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EH-TW5800 and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson EH-TW5800 projector, Epson ELPLP49 projector lamp, Epson projector lamps

3 steps to a new Mitsubishi WD-82742 RPTV lamp

Shelagh McNallyPosted on November 27, 2012 Posted in FixYourDLP, Rear Projection TV Lamp Replacement — No Comments ↓

Follow our 3-step guide to a new Mitsubishi 915B455011 / 915B455A11 lamp in the Mitsubishi WD-82742 RPTV.

Step 1: Know when to replace

The first indication that the Mitsubishi 915B455011 / 915B455A11 lamp needs to be replaced is a picture that is becoming dimmer.

When you see the RED light on the front control panel on your Mitsubishi WD-82742 RPTV, it’s also time to replace the lamp immediately.

When the TV is operating normally, this indicator will not be lit. When has turned RED, the lamp has burnt out and since this is the only source of light for the TV, it will not turn on. Replace the Mitsubishi 915B455011 / 915B455A11 lamp immediately.

Step 2: Buy authentic

It’s important that you install an OEM lamp and avoid a generic, compatible RPTV lamps.

Knock-off, compatible generic lamps may seem like a bargain in the beginning. They actually cost more in the long run since they can damage the color wheel and ballast mechanisms in your RPTV. They also give off poor light, are prone to messy explosions and actually have a shorter life.

There are also health concerns associated with these lamps. Generic lamps are made with toxic substances that can compromise your family’s health. Read more about the dangers of Krypton-85.

When you purchase an OEM replacement lamps you’re guaranteed the best lamp for your RPTV.

We recommend purchasing from an Authorized Philips dealer such as Discount-Merchant.com to insure that you are receiving a genuine Philips brand replacement lamp. Beware of knock-off and counterfeit Philips lamps floating around in the market.

Advantages of OEM lamps

• Brilliant brightness and luminosity: Your OEM lamps has been built to work in harmony with every component in your RPTV. Keep the optics, power supply, electronics and processing algorithms in sync to provide the best image possible – the reason who invested in an RPTV.
• Color: Genuine lamps have the correct technology to give the correct optical alignment of your color wheel and give consistent color across the whole screen.
• Safety: Your RPTV operates at extremely high temperatures. The quartz, glass and wires in your lamp have to be able to withstand the high pressure heat. Scruplous OEM manufacturers lamps have tested their lamps for safety. Generic manufacturers have not.
• Lamp Life: Only OEM lamps have the durability to work for their entire lifespan. Only genuine lamps give you the guaranty of full life performance along with a money back guarantee. Installing a generic knock-off lamp will void your warranty and should any damage be done to your RPTV you’re on your on for repairs. Why threaten the investment you’ve made in your RPTV to sake a few dollars?

Learn the 7 Ways to spot a counterfeit lamp.

Installing the new Mitsubishi 915B455011 / 915B455A11

Before installation: Turn off the TV and allow it to cool for one hour. Failure to do so can put you at risk of burning yourself since the Mitsubishi WD-82742 operates under high heat.

TIP: Use a pair of rubber gloves during installation. These lamps contain mercury, which may end up on your skin. Don’t touch the lamp glass with bare hands as the oil form your fingers may cause premature lamp failure.

After TV has cooled, turn the TV around to access the lamp cover located at the back of the Mitsubishi WD-82742 RPTV.

Using a #2 Philips screwdriver, loosen the screw holding the cover in place. Put the cover to one side.

Loosen the screw securing the lamp cartridge, releasing it from the mating threads. This is a captive screw so it will not be separated the lamp cartridge.)
When the screw is loosened, gently grasp the handle on the lamp cartridge and pull the lamp straight out. DO NOT TILT, as there may be glass fragments that will fall inside the TV.
If this happens, carefully pick up the larger shards wearing rubber gloves. Take a cloth just damp enough to pick up the small shreds. It’s important to pick up the broken lamps since this lamps does have mercury. Read more about proper clean-up from the EPA.
Learn what to do should the bulb shatter.
Take out the bag supplied with your new lamp and open it up. You’ll store the old lamp in this bag.
Put the old lamp gently into the opened bag. Close the bag.
Gently slide in the new Mitsubishi 915B455011 / 915B455A11 Lamp into the slot, making sure not to tile the lamp.
Tighten the screw in the lamp.
Replace the cover on the Mitsubishi WD-82742 and tighten the screws.

NOTE: The Mitsubishi 915B455011 / 915B455A11 Lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer, they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Learn how to extend the Mitsubishi 915B455011 / 915B455A11 Lampby reading 7 Tips for extending RPTV lamp life.

Tagged with: authentic lamps, genuine lamps, Lamp replacement, Mitsubishi 915B455011 Lamp, Mitsubishi 915B455A11 lamp, Mitsubishi WD-82742, Mitsubishi WD-82742 RPTV lamp, troubleshooting

How to install a new Epson EH-TW5500 projector lamp

Shelagh McNallyPosted on November 27, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — 2 Comments ↓

Replace the Epson EH-TW5500 projector lamp with this guide

When it’s time to change your Epson EH-TW5500 projector lamp, you’ll see a replacement warning message on the screen. You’ll also notice an orange blinking light on the projector.

This is the lamp replacement indicator letting you know it’s to replace your Epson EH-TW5500 projector lamp

You can expect 3900 hours of lamp from the lamp depending on the settings and usage of the Epson EH-TW5500.

The importance of authentic lamps

When it’s time to change your Epson ELPLP49 projector lamp, it’s important to buy only a genuine lamp to replace the old lamp. The price of counterfeit knock-off lamps may be tempting but can cost you more money in the long run. Counterfeit lamps are not manufactured according to Epson’s specifications and can damage the sensitive (and expensive) mechanisms in your Epson EH-TW5500 projector.

Buy a Epson ELPLP49 lamp from a recognized dealer to get a far superior product with a replacement guarantee and tech support. Learn the 7 Ways to spot a counterfeit lamp.]

Find this authentic lamp on Amazon sold by these authorized dealers:

6 reasons to avoid generics

generics have a shorter lamp life than original lamps
compatible are created with toxic materials and carcinogenic parts including Krypton-85
knock off lamps are prone to explosions
generic lamps damage the sensitive electronics in your projectors
when you buy copy-cat lamps you get no guarantee or refunds
installing a generic lamp voids your projector’s warranty.

Step-by-step instructions

Before installation:

Turn off the projector and unplug the AC cord.
Allow the Epson EH-TW5500 to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover for the Epson EH-TW5500 is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the lamp cover.

2. Remove the two screws on either side of Epson ELPLP49 lamp. Place the screws to either side.

3. Pull the lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4, Take the new Epson ELPLP49 lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

5. Replace the Epson ELPLP49 screws on the newly installed lamp.

6. Re-connect the lamp cover. Tighten the screws on the cord and turn on the Epson EH-TW5500 projector.

7. Re-attach the power cord. Turn the projector on and let it warm up.

8. Reset the Lamp Operating time.

Resetting the Epson EH-TW5500 Lamp Operating Time

Reset the Epson EH-TW5500 Lamp Replacement Counter only when the Epson ELPLP49 lamp has been replaced.

Turn the Epson EH-TW5500 projector on.
Press MENU to display the configuration menu.
Press the down arrow to move down the menu to the Reset option.

Press Enter to enter the Reset Menu.
Press the down arrow to move down the menu to the Reset Lamp Hours option.
Press Enter.

When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
Use the cursor to move to the YES option.
Press Enter to reset the lamp hours to zero.

Prolong the life of the Epson ELPLP49 lamp:

Extend the life of the newly installed Epson ELPLP49 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EH-TW5500 and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson EH-TW5500 projector, Epson ELPLP49 projector lamp, Epson projector lamps

Replacing the Mitsubishi WD-73842 RPTV lamp

Shelagh McNallyPosted on November 27, 2012 Posted in FixYourDLP, Rear Projection TV Lamp Replacement — 2 Comments ↓

Follow this step-by-step guide for replacing the lamp in the Mitsubishi WD-73842 RPTV.

When the picture on your Mitsubishi WD-73C12 RPTV becomes dimmer it’s time to replace the Mitsubishi 915B455011/915B455A11 lamp. When the lamp is no longer working the Status Light on the front of the Mitsubishi WD-73842 panel will begin blinking red.

Since the 915B455011 / 915B455A11 lamp is the only source of light for the TV when it has reached its end of life, the Mitsubishi WD-738422 will not turn on.

Invest in an authentic lamp

Buy your Mitsubishi 915B455011/915B455A11 lamp from an authorized manufacturer and avoid the lower-priced generic lamps. These knock-off lamps are made with inferior, counterfeit parts that can damage the sensitive mechanisms in your Mitsubishi WD-73842 RPTV. These generic lamps advertise as compatible but may end up costing you more since they have a shorter lamp and are prone to explosions. Buying an authentic lamp from a legitimate source keeps your projector under warranty and gives you a solid guarantee that the lamp you are installing is suitable for your projector.

Learn the 7 Ways to spot a counterfeit lamp.

Installing the new Mitsubishi 915B455011/915B455A11

Before installation: Turn off the TV and allow it to cool for one hour. Failure to do so can put you at risk of burning yourself since the Mitsubishi WD-73842 operates under high heat.

After TV has cooled, turn the TV around to access the lamp cover located at the back of the Mitsubishi WD-73842 RPTV.

Using a #2 Philips screwdriver, loosen the screw holding the cover in place. Put the cover to one side.

Loosen the screw securing the lamp cartridge, releasing it from the mating threads. This is a captive screw so it will not be separated the lamp cartridge.)
When the screw is loosened, gently grasp the handle on the lamp cartridge and pull the lamp straight out. DO NOT TILT, as there may be glass fragments that will fall inside the TV.
If this happens, carefully pick up the larger shards wearing rubber gloves. Take a cloth just damp enough to pick up the small shreds. It’s important to pick up the broken lamps since this lamps does have mercury. Read more about proper clean-up from the EPA.
Learn what to do should the bulb shatter.
Take out the bag supplied with your new lamp and open it up. You’ll store the old lamp in this bag.
Put the old lamp gently into the opened bag. Close the bag.
Gently slide in the new Mitsubishi 915B455011 / 915B455A11 Lamp into the slot, making sure not to tile the lamp.
Tighten the screw in the lamp.
Replace the cover and tighten the screws.

Learn how to extend the Mitsubishi 915B455011 / 915B455A11 lamp life in by reading 7 Tips for extending RPTV lamp life.

Tagged with: authentic lamps, genuine lamps, Lamp replacement, Mitsubishi 915B455011 Lamp, Mitsubishi 915B455011/915B455A11 lamp, Mitsubishi 915B455A11 lamp, Mitsubishi WD-73842 RPTV, replacement lamps, troubleshooting

3 Steps to a new Mitsubishi WD-73742 RPTV lamp

Shelagh McNallyPosted on November 27, 2012 Posted in FixYourDLP, Rear Projection TV Lamp Replacement — No Comments ↓

Follow our 3-step guide to a new Mitsubishi 915B455011 / 915B455A11 lamp in the Mitsubishi WD-73742 RPTV.

Step 1: Know when to replace

The first indication that the Mitsubishi 915B455011 / 915B455A11 lamp needs to be replaced is a picture that is becoming dimmer.

When you see the RED light on the front control panel on your Mitsubishi WD-73742 RPTV, it’s also time to replace the lamp immediately.

Step 2: Buy authentic

It’s important that you install an OEM lamp and avoid a generic, compatible RPTV lamps.

There are also health concerns associated with these lamps. Generic lamps are made with toxic substances that can compromise your family’s health. Read more about the dangers of Krypton-85.

When you purchase an OEM replacement lamps you’re guaranteed the best lamp for your RPTV.

Advantages of OEM lamps

Learn the 7 Ways to spot a counterfeit lamp.

Installing the new Mitsubishi 915B455011 / 915B455A11

Before installation: Turn off the TV and allow it to cool for one hour. Failure to do so can put you at risk of burning yourself since the Mitsubishi WD-73742 operates under high heat.

After TV has cooled, turn the TV around to access the lamp cover located at the back of the Mitsubishi WD-73742 RPTV.

Using a #2 Philips screwdriver, loosen the screw holding the cover in place. Put the cover to one side.

Loosen the screw securing the lamp cartridge, releasing it from the mating threads. This is a captive screw so it will not be separated the lamp cartridge.)
When the screw is loosened, gently grasp the handle on the lamp cartridge and pull the lamp straight out. DO NOT TILT, as there may be glass fragments that will fall inside the TV.
If this happens, carefully pick up the larger shards wearing rubber gloves. Take a cloth just damp enough to pick up the small shreds. It’s important to pick up the broken lamps since this lamps does have mercury. Read more about proper clean-up from the EPA.
Learn what to do should the bulb shatter.
Take out the bag supplied with your new lamp and open it up. You’ll store the old lamp in this bag.
Put the old lamp gently into the opened bag. Close the bag.
Gently slide in the new Mitsubishi 915B455011 / 915B455A11 Lamp into the slot, making sure not to tile the lamp.
Tighten the screw in the lamp.
Replace the cover and tighten the screws.

Learn how to extend the Mitsubishi 915B455011 / 915B455A11 Lamp. Read 7 Tips for extending RPTV lamp life.

Tagged with: authentic lamps, genuine lamps, Lamp replacement, Mitsubishi 915B455011, Mitsubishi 915B455011 Lamp, Mitsubishi 915B455A11, Mitsubishi RPTV, Mitsubishi RPTV lamps, Mitsubishi WD-73742, replacement lamps

Replacing the Epson EH-TW5000 projector lamp

Shelagh McNallyPosted on November 26, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Replacing the Epson EH-TW5000 projector lamp is quick when you follow guide

When it’s time to replace the Epson EH-TW5000 projector lamp you’ll notice the lamp replacement light begins blinking red and then changes to orange. A replacement warning message will also appear on screen. Replace the lamp immediately when the light is blinking orange. Don’t wait!

Find this authentic lamp on Amazon sold by these authorized dealers:

Why OEM lamps are important

Shopping for your new Epson ELPLP49 can get kind of confusing. There are a multitude of choices out all claiming to be “compatible” with your Epson projectors. The first step to finding the best lamp for your Epson EH-TW5000 is to consider the source? Buying North American lamps.

Generics just don’t have the same quality and actually have a shorter lamp life than original lamps. So while they make appear to have better prices, they actually cost more in the long run. There are also safety concerns.

Counterfeit manufacturers don’t have the same equipment or materials and resort to using toxic subsitutes such as Krypton-85 — a highly carcinogenic material. The gas can escape when the lamp breaks and unfortunately these generic “compatible” lamps are prone to explosions. Too often generic lamps damage the sensitive electronics in your projectors

Buying authentic lamps guarantees a lamp manufactured to work with your projector If you do decide to go with a cheaper compatible lamp then buy one from a registered OEM manufacturer who is building them in North America Buy authentic and get a better product plus better customer care.

How to install

Before installation:

Turn off the projector and unplug the AC cord.
Allow the Epson EH-TW5000 to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover for the Epson EH-TW5000 is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the lamp cover.

2. Remove the two screws on either side of Epson ELPLP49 lamp. Place the screws to either side.

3. Pull the lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4. Take the new Epson ELPLP49 lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

5. Replace the Epson ELPLP49 screws on the newly installed lamp.

6. Re-connect the lamp cover. Tighten the screws on the cord and turn on the Epson EH-TW5000 projector.

7. Re-attach the power cord. Turn the projector on and let it warm up.

8. Reset the Lamp Operating time.

Step 3: Reset the Epson EH-TW5000 Lamp Timer

Reset the Epson EH-TW5000 Lamp Replacement Counter only when the Epson ELPLP49 lamp has been replaced.

Turn the Epson EH-TW5000 projector on.
Press MENU to display the configuration menu.
Press the down arrow to move down the menu to the Reset option.

Press Enter to enter the Reset Menu.
Press the down arrow to move down the menu to the Reset Lamp Hours option.
Press Enter.

When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
Use the cursor to move to the YES option.
Press Enter to reset the lamp hours to zero.

Prolong the life of the Epson ELPLP49 lamp:

Extend the life of the newly installed Epson ELPLP49 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EH-TW5000 and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson EH-TW5000 projector, Epson ELPLP49 projector lamp, Epson projector lamps

Install an Epson EH-TW3800 projector lamp in 3 easy steps

Shelagh McNallyPosted on November 26, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Install a new Epson EH-TW3800 projector lamp in 3 easy steps

When it’s time to replace the Epson EH-TW3800 projector lamp you’ll see the orange warning light begin to blink on your projector.

A replacement warning message will also appear on screen. You can expect 3900 hours of lamp from the lamp depending on the settings and usage of the Epson EH-TW2900.

Step 1: Buy authentic

The Internet has been flooded with generic lamps stating they are “compatible” with Epson projectors. Consider the source before purchasing. Look for a registered OEM manufacturer in North America using the correct materials and specifications. Generic lamps have a long list of problems and while they may seem like a bargain, they actually end up costing you more.

Find this authentic lamp on Amazon sold by these authorized dealers:

6 reasons to avoid generics:

generics have a shorter lamp life than original lamps
compatible are created with toxic materials and carcinogenic parts including Krypton-85
knock off lamps are prone to explosions
generic lamps damage the sensitive electronics in your projectors
when you buy copy-cat lamps you get no guarantee or refunds
installing a generic lamp voids your projector’s warranty.

Your Epson EH-TW3800 is a sophisticated machine with sensitive electronic components. An authentic Epson ELPLP49 projector lamp has been designed specifically to keep your projector operating at optimum levels. Learn How to buy an authentic lamp.

Step 2: Install a new Epson ELPLP49 lamp

Before installation:

Turn off the projector and unplug the AC cord.
Allow the Epson EH-TW3800 to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover for the Epson EH-TW3800 is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the lamp cover.

2. Remove the two screws on either side of Epson ELPLP49 lamp. Place the screws to either side.

3. Pull the lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4. Take the new Epson ELPLP49 lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

5. Replace the Epson ELPLP49 screws on the newly installed lamp.

6. Re-connect the lamp cover. Tighten the screws on the cord and turn on the Epson EH-TW3800 projector.

7. Re-attach the power cord. Turn the projector on and let it warm up.

8. Reset the Lamp Operating time.

Step 3: Reset the Epson EH-TW3800 Lamp Timer

Reset the Epson EH-TW3800 Lamp Replacement Counter only when the Epson ELPLP49 lamp has been replaced.

Turn the Epson EH-TW3800 projector on.
Press MENU to display the configuration menu.
Press the down arrow to move down the menu to the Reset option.

Press Enter to enter the Reset Menu.
Press the down arrow to move down the menu to the Reset Lamp Hours option.
Press Enter.

When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
Use the cursor to move to the YES option.
Press Enter to reset the lamp hours to zero.

Prolong the life of the Epson ELPLP49 lamp:

Extend the life of the newly installed Epson ELPLP49 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EH-TW3800 and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson EH-TW3800 projector, Epson ELPLP49 projector lamp, Epson projector lamps